Hi. After DPF EGR SCR off have dtc 14B100 and 1A2600. No leak, I check. I read that such errors can appear after incorrectly disabling the EGR...
Who can help disable EGR?
Hello,
please help to get the incode for renault who has the access for renault server
outcode : A53APVSB7SVL4113S4J1EFG5
vin : VF1JP3B0541210928
UCH is vergin
Thanks in advance
Can you please help with this BCM file - car cranks and doesn't start.
Error codes:
B10D7 - PATS key
U0100 - Lost Comms with ECM/PCM
U0151 - Lost Comms with Restraints Control Module
B109B - License Plate Light
B1099 - Right Position Light
B1D06 - Left Turn Indicator
B1D01 - Right Low Beam
U1000 - Solid State Driver Protection Activated - Driver Disabled
U3000 - Control Module
Hi to All!
Help please with this dinosaur to make Euro2 (cat off)
Nissan Almera 1.8 2001
Hitachi MEC20-705 SH705507N
1MCM46E5 14U205
without p0000 and pFFFF
Thanks in Advance!
Hello!
Please can help me someone to delet the P1144 dtc please?
I tried some solutions but something it's not ok and I wan't to make a comparasion.
Thank you!
Hello, i need some PSA expert or MD1CS003 full flash that is from car that has:
130 hp(electronic wastegate), 1 can line ABS, Manual gearbox and key(this is important, cause it cant be coded) and the most important is ADAS system.....
Till now doesnt metter what flash i use i have adas yellow warning light and warning writing about fail on dash about this fuking system.... It complains on collision detect system...
I am swapping ecu from locked one to unlocked and trying to get correct flash for it, but this system is the only thing that is left to fit...
Hi. I need a wiring diagram for 10 pin full led lights for mazda cx-3. After the facelift something changed and the diagram I have fits older headlamps, but newer ones are wired differently. can anyone help? thanks.
I have a non starter. They replaced steering column lock with a brand new one and after that the convenience control unit is not waking up anymore. No ignition. Convenience module and wiring is ok. For me it looks like the steering lock module is not adapted but I don't have that much experience. But when I try to adapt it with vcds and press Test Button, I only get n.i.O what translates to not ok. I use the immo code from ecu. I hope that the masterminds of this forum can help me.
In short: Steering lock unit replaced with new one, convenience module no response on the canbus, no ignition.
Flashed a Skoda 2017 DCM6.2 ecu with Autotuner without error, but after flashing immo is active and i can`t flash it anymore.
Also with ODIS-E no flash possible because immo is active
Someone here who can help me rremote, ODIS-S 23.01 and ori VAS 6154A is avaivble
Hello guys. I am trying to coding out O2 sensos and cat heating on my W203 200k with Siemens SIM4LE. I know that remap is best option, but this ecu need to open and desolder flash and i am not good with that. I know that this can easy coding out with dts monaco, but obviously can't unlock variant coding properly. I willing to pay for help.
Hi everyone,
Currently own a W166 350 Bluetec MY12 with code U42 in specsheet. Since the two years that I've owned it the SCR module N118/5 has never appeared in Xentry reports as a separate module. I have tried to check the adblue level in IC172 and it has always shown "not full" even though I have filled it several times. What I have noticed is that the adblue consumption has been very low like 1l per 8,000km, which I though was due to the car being used only on long highway runs.
I have checked in CR60LS and EIS166 and SCR is active.
Also did some search in EPC and discovered that even though the part number for N118/5 has changed thoughout the years the hardware number has remained unchanged.
In this regard due to suspicions of the previous owner having shut the system down, does anyone with a W166BT MY12 confirm that ECU N118/5 appears in Xentry reports as a dedicated ECU?
![[Image: 49461378ie.jpg]](https://up.picr.de/49461378ie.jpg)
