Have faulty transtron ecu, need to clone it.
Did read data with ktag from ori and write to donor but immo still on.
Is there eerpom hiding somewhere in the board what i can`t find?
Ktag readed only MPC file, no eeprom or flash aavailable.
I need help to find eeprom on board on this bosch ecu from Golf 4 SDI to make immo off..I think that chip is ST24C04 but not 100% shure..I dont have board picure to upload
Hello,
Have mb w213 hybrid with fault b284f13-the squib for pyrofuse 'High voltage on-board electrical system' has a malfunction. There is open circuit
Do anyone know where this fuse located?
Hi All.
I need orginal file for Opel Zafira C problem is with scr somone switch off scr and now is on display low addblue and left 204km to stop start engine and stack on this. I cant do restest. Somone help with this , orginal file or repair this .
Hi! I need help with dpf&egr off for vw 1.6 cayc simos PCR 2.1 . ( 03L 906 023 GL)
I make DPF soot reset before write(but light on dash is still active) , i tried solution ads , Davinci but no work, Car still in limp mode and dpf light is on.
Can someone help me?
Thanks!
On my last PIWIS install the power button (bottom left) shut down the computer. On my new one it exits the application back to the desktop. Does anyone know how to change the action of this power button? Tried looking in registry but cannot see anything. I found it really useful to shut down the computer with one button press.
Also, any wat to get rid of the yellow triangle (Licence update required in xxxx days) from the bottom left?
Hi, can someone find out the code and turn off the CAN check? It shows CODE ERROR in the car and on the table. It's a FIAT Delphi model F199FL EUR (year 2013)
HW ver:28252883
SW:16
prod date:1910
7355014090
eeprom 24LC32
hello friend
i have mercedes w221 edc16cp36 ecu .i want to remove complete intake runner (M5)
car have 253000 erorr(p2009)
somebody have solution then please help me
thank you
i offer remote service for change VAG car region!
Unit: Mhi2(Harman) or Mh2p(Alpine)
Mib2 generation: MMI, PCM4, PCM5, etc
Note: Mib3 impossible conversation without open Unit !
Convert between the following regions:
EUROPE - NAR (USA, CA) - ROW (rest of world) - ASIA (Japan, Korea, China) - UAE …
Tools needed
1: laptop windows
2: adapter ax88772
3: LAN rj45 cable
4: SD card
changes included: Navigation (Map) ; Radio frequency ; Fullscreen Apple Carplay + Android Auto ; Language ; activate all FEC …
hello, im finding original file of fiat talento with md1cs006
i read flash from ecu, with adblue off (not good solution).
im search for original file.
Driver:
RENAULT
TC 298 TP - Renault
MD1CS006
Aurix TC298TP
HSM R/W Protect: 0x18000 -- 0x1BFFF
HSM R/W Protect: 0x60000 -- 0x6FFFF
HSM R/W Protect: 0x70000 -- 0x7FFFF
Virtual OTP Protect: 0x00000 -- 0x1BFFF
Virtual OTP Protect: 0x60000 -- 0x7FFFF
SW Num:10SW066183.
SW Num:10SW066183.
SW Num:10SW050224.
if i find the same software with adblue on, can i copy juste map without otp and i write it in the ecu, there are software to do this ? ,thank you
thank you
Hi. I have an Audi A6 C8 from USA after conversion to EU. Before conversion rear turn signals were dynamic, after it they are not. How to code it to obtain dynamic singnals?
I have a VCDS and VCP. I don't have ODBeleven.
![[Image: image.png]](https://i.postimg.cc/8PzL6C2H/image.png)
![[Image: a618f7d3713043ea11e438d83659485f.jpg]](https://uploads.tapatalk-cdn.com/20250410/a618f7d3713043ea11e438d83659485f.jpg)
