Is there anyone out there that could help me disable or delete the dtc U1014 from the flash memory of my Bosch ESP 9.0i abs unit? I have retrofitted a part which has triggered this code and it will not clear regardless of how I code the module. Flash file attached
AKL on a 2013 Porsche Cayenne and Autel corrupted the P-Flash during backup. Used VVDI-Prog to unlock and wrote different P-Flash from different BCM but when tried to learn keys the BCM is not detected. Tried different P-flash (2nd one) and I had the BCM relays clicking. I think I have the wrong P-flash, so I'm hoping to find one compatible with 7PP907064EM which is the BCM part number that I'm working with.
My files are triple checked, the D-flash didn't get corrupted and it was verified after writing it back to the BCM, but I think the P-flash is the problem since I used one from a different 5M48H based BCM. I've checked the pcb and there are not shorts or open traces, my diode and zero ohm resistor are soldered back properly so is the cut at the quartz oscillator.
I've scoured the Internet for a P-flash file that matches my BCM part number but so far no luck. Like I said, I already tried two P-flash files and one of them triggers relays in the BCM, the other one is making the BCM not detected when I plug it in the vehicle and try to learn the keys.
It's my first attempt at this BCM and in hindsight, I should have only backed up the D-flash but wanted to have a backup of both flash files just in case something went wrong. Won't be making this mistake again.
I hope someone can help or come up with some ideas as I'm all out of gum.
Hello,
retrofitted W212 preFL front bumper into AMG and changed DRL lights from ''straight'' into ''hockey'' now after engine start it goes on as it should, then flashes few times , after that I am getting error of both DRL's in instrument cluster. After that DRL's stays on but dimmed.
I replaced the backup camera module with a used one, and I need to change the VIN on the module to match my car. I saw the VINs in Monaco, but I can't find a way to code it.
Hello,
Mercedes Benz W204 C200 CGI, with the M271.860 Engine and the 5 speed AT (722.6).
DTCs P0049, followed by limp mode until the car is shut down and the DTC cleared.
The fault appears mostly with heavy throttle application, especially when requesting kick-down.
Gentle driving and progressive throttle application to peak boost on my tune (set to ~1.8 bars peak) does not throw the fault.
Hey, if swapping front bumper from different car and has better looking parking sensors than old bumper , does require coding them to the car? Can this be done via xentry or need to use dts monaco?
Thanks in advance for aby help much appreciated
Does anyone know any tool that calculates the checksum for MRD1 (MD1CP001)?
Read done with - Xhorse MultiProg
Tunne - Swiftec (no plugin for Winols).
But I have nothing to do checksum for this ECU and haven't figured out which one does.
Hello. Can anyone help clone the MG1CS001 VAG ECU? The new ECU is Virgin. I copied IntFlash and Eeprom from the old ECU but it didn't help. I know you can do ODIS but I don't have ODIS. I don't have a car either, only the ECU. I am attaching the files of the old and new ECU. Regards
We have a VW caddy, 2012 1.6 with CAYE engine. Got a fault with it "P0652 - reference voltage B circuit low." And another fault for crank sensor circuit.
Symptoms, long starting and limp mode, coil light flashing.
Caddy has a brand new crank sensor installed so that's eliminated. Going through the wiring diagrams, there are 3 wires from the ECU directly to the crank sensor through the loom. Pin 1 and Pin 2 are 5V and Pin 3 is ground. Pin 1 has little to no voltage which I believe is the problem for this circuit low fault, pin 2 has a good solid 5V and ground is good. For pin 1 on the crank it goes to pin B25 on the engine ECU, no 5V coming out the ECU. The next step taken was try 2x donor ECUs, PCR2.1, fault remains, checked the wiring to and from the crank sensor, all ok. Checked all the wiring on the loom to connector "B" on the engine ECU, all good. Checked all the powers and grounds to the engine ECU, all good. Checked fuses, relays and again all good.
The weird thing is, I've had 5V very intermittently from pin B25 on engine ecu.
I've had a look at other 5V circuits on the ECU, I.E cam sensor, map, maf, EGR, etc.. all seem to be ok. I've tried unplugging all 1 by 1 and even all together to see if I get 5V back on B25, no improvements. From my understanding there is only 1 component for the crank sensors 5V supply where as the other supplies does other components at the same time.
Any suggestions or has anyone experienced or knows anyone that experienced this fault?
Hello. I need virginize Id box and smart key module in 2013 Toyota Auris 2 hybrid. Car after crash , and long repair it doesn't start. There is no DTC . I maked ecu synchronization (DLC 4 and 13) no start. I transferred the idbox, smart key, Tcm, Power hybrid, and ecm modules from another car and the car started, that why i think is some thing not right with idbox and smart key synchronization. Can some one halp me? THX
So a friend tried tune his car with Kess and now it wont start or connect thru OBD, so i guess he need ori file so he can restore it with KTAG. Anyone can help us with the file?
Posted by: Desctop - 02-08-2025, 12:25 AM - Forum: Selling Box
- No Replies
One Seller for all your John Deere GPS Precision needs
Equipment and Remote Activations!
For sale i currently have: John Deere GS3 Command center display. Used but works like new, no issues.
For Sale $1,000 USD
John Deere Gen 4 Extended Monitor. Used but works like new, no issues.
For Sale $1,000 USD
Starfire 3000 Antenna with SF1 Activation. Used but works like new, no issues. For Sale $1,100 USD
Starfire 6000 Antenna with SF1/SF3 And RTK Permanent Activation. For Sale $3,450 USD
Starfire 7000 Antenna with Permanent RTK and MRTK. For Sale $6000 USD
We also have for sale:
Greenstar display: 2600,2630,4640.
Starfire receivers: 3000,6000,7000
Also i can do Activations/Subscriptions Starfire 3000:
SF2 ready
RTK ready
1 year SF2 Subscription
mRTK 5 years
Starfire 6000:
SF3 ready
RTK ready
1 year SF3 Subscription
mRTK 5 years
PIN Code Remove 6000
NOW AVAILABLESTARFIRE 7000
SF RTK 1 year
RTK Permanent
I also can activate more activations if desired, feel free to message and ask!!, Prices are very competitive, and fair! For more information don't hesitate to message me! You're welcome!!!
![[Image: QnUfn61]](https://imgur.com/a/QnUfn61)