Hello everyone, I recently bought a Canadian W204 2012 FL that unfortunately had halogen headlights. I'm from Europe and most of the cars here have Bixenon ILS headlights so I bought a pair of 2 OEM headlights(spare parts). Both harness connectors are the same, there's just 2 or 3 additional wires for leveling I guess which I'm planning on adding later.
When the ignition is On, everything on the headlights works like it should. "C" led turns on, turn signal works and low beam lights up. When you start the car the low beam started flickering before after few seconds but a friend of mine managed to fix it with "Launch" so it's working like it should. My guess is he got to the "Xenon Present" option somewhere.
"C" Led turns off 5-10 seconds after the low beam lights up and throws error on dash. Turn signal works fine on the 1st blink but then it starts to flicker when blinking on the 2nd, 3rd, etc while throwing turn signal error on dash.
I've aligned the headlights manually so they're not blinding anyone and in the spring I'm planning on adding the required additional wires, harness for leveling sensors, sensors themselves and whatever is necessary to make them self level and cornering if possible. I'd be grateful if someone can shed some light on this. Right now I just want to get the turn signal work properly and the "C" led, low beam works great and then I'll work onto the other stuff. In fact I'd love to get the "C" led work all the time with the DRL and side lights.
Can someone please clone my pcr2.1
both part number is different
original car part no is - 03L 907 425 B
donor ecu part no is = 03l 907 023 NT
need to transfer data in both files flash and eeprom
(02-08-2025, 04:58 PM)afroz07 Wrote: Can someone please clone my pcr2.1
both part number is different
original car part no is - 03L 907 425 B
donor ecu part no is = 03l 907 023 NT
need to transfer data in both files flash and eeprom
please brothers help
its urgent
because one of my working boy dead ecu by mistake thats the reason i have to change ecu
thankss
Máy phân tích có thể.
Hướng dẫn đầy đủ trong file.Hỗ trợ
Arduino..... hoạt động tốt với chương trình từ Canhacker, phiên bản CARBUS Analysis v0.4.10 hỗ trợ giao thức Lawicel mà không cần thay đổi bất cứ điều gì trong bản phác thảo, không bị trễ hoặc treo.
Đây không phải là công việc của tôi, hy vọng nó giúp ích cho bạn
Liên kết không có mật khẩu. Tải xuống và tận hưởng
First of all, I want to apologize to the Mhhauto moderator team, but I'm sorry if there is a similar post, I searched but couldn't find one.
I have a problem with my Odis engineering 18.1.0, the problem is when i use Odis E, the product (hardware) vxdiag-vcx se, make a connection with auto and control modules but odis e doesn’t show any measuring values and stuff like that. I hope someone can help me thanks.
Hello,
A friend ask me is possible to do StartStop off via coding or something like that? when yes how?
I have launch and Ista (not ori)
Because ECU is locked and he will not unlock yet.
Maybe someone know it
Does anyone have details of getting CCP communications with a DQ250 from a R32 golf from around 2006? Assuming that it is CCP/XCP, but does anyone have details of the CRO/DTO IDs, or any seed key? Perhaps a KW service to enable it if it isn't already? I don't have a car yet, but will get one from that year as a project.
I need the original ecu map, a remapping from some Finnish "tuneshop" and now the car does not work and I cannot check fault codes because the engine DTC has been disabled. yesterday i tried reading engine errors xentry, star, autocom, delphi, wurth. and the works all the modules but not the engine DTC
I have a problem with a Claas Axion 940 with edc17uc31 ecu.
I'm trying to remove adblue but no matter what solution i try tractor goes in limp mode after 5-10minutes, with DTC 7EF0 - Parameter not available.
I try more that 5 files, wite with Fgtech or Flex, no matter what i do, still limp mode after a while.
Whith original file tractor work ok. DCU ecu is still plugged in and working.
Anyone have a good solution? I can pay whitout problem for a good solution.
hello All
i need database that show i can put the injector part number it shows what Nozzle and Valve number and exact bar
i have eps200 database but it not shown the nozzle or the valve
i heard it's stage 3 software so if anyone have it or link i can download it from i'll be so grateful
thank you all
I have ISTA 4.49.23 with SDP 4.51.20 standalone working as expected. Diagnostics, coding, and programming are all functioning well, and the troubleshooting guides are displaying correctly. However, the operations report is not showing and instead displays the following error in the attached image.
I might be missing some file or have something corrupted somewhere.
Hello all, is it possible to do hard cut limiter in hpt? If so, could someone help me to make it happen? I have 3 diff files I would like to add limiter too. Cummins L5P and Powerstroke.
![[Image: IjaDwSW.png]](https://i.imgur.com/IjaDwSW.png)
