Hi I have problem with Opel Insignia Blind Spot Sensor. Original sensor was water damaged and MCU wasn't possible to read. I have second hand module from american GM cadilac car. What can be determined by VIN. When i plug this module to car i had 2 dtc's Module not programed and Vin number not programed i try to read MCU from this module and change VIN and now i have only 1 DTC B101E:41 Module not programed I heard about modules from GM american cars has other software then opel modules. Maybe someone have a dumps from opel module?
I share pinouts, wiring and my memory dumps from my module for everyone
When reading mcu you must connect external 3v3 supply to jtag and desoleder marked 1k resistor from reset line.
When you want to diagnose module connect 12V to socket like on pinout and GMLAN Low Speed to pin no. 1 obd socket. When module don't wake up apply the 3V3 to MCU
helou friends please can you check my file if it is original or modified
Siemens Sid 803
HW T3NISE63FO06C00
SW 10081860AA
i have problem with with fault P0002-61 fuel valve ... Car already has new fuel pump , new injector, new fuel presure sensor , new fuel sender , fuel hoses are changed... and still in full load on 5 speed gear is fault back , but engine goes without emergency mode...
i try dtc off with dtc remover but without succes ... with other software dtc on diagnostic not seen in PCM but limp esp with fault from PCM .... thank for help
I have a 2023 Infiniti QX60 and need to calibrate the steering angle sensor but the CGW is locked and won't allow me to do it. I don't have online access for Consult to unlock the gateway and my launch Pad also won't do it. Does anyone have online access that can unlock for me, please pm
my friends did the coding to his MINI R55 (06/2009) and deleted VO/FA from the CAS AND FRM, now i can't do the default coding because he deleted VO/FA from the modules.
VO/FA is stored in those two modules, how can i create a new VO/FA to get it again working ?
His seated heaters and windschield heat doesnt work.
I need help with the airbag module f01g07203l. Bosch. I read the eeprom 95640 and bought the crash delete file, since then I have the error b1499 and b 1498. can you help me? thank you
Hi all,
I've tried searching but could not see a clear answer, and I know there will not be just one
What I would like to know is what is the best way to create a CAS3+ Dump from a 2009 BMW
I understand this will be the encrypted version based on the year.
I'd like to do a full dump / backup - is this just Flash & EEProm or is there more?
What Tools and Software is recommended for this and any DIY guides.
I'd like to verify the backup obviously
I have a R270+ (china) and IPROG and DigiProg3 XTOOL XPAD 100
Also want to do the same backup for the Kombi (Dash)
Whats peoples preference here
Hi,
i have Mazda6, year 2007, 2000cm3, 143Hp with integrated FFH Webasto.
Most times i drive on short locations and may be this block my heater.
As i red if i use car for less than 5min heater count this as not
successful star and after some not successful it block heater.
I remove fuse for HEATER for 3 hours, then connect it and
read my car with Forscan.
There is no errors, but i try livedata for heater and there is
LOCKOUT : Locked.
I use service procedure FFH reset but it is still in locked status.
Did i need to try to connect to heater with Webasto Thermo Test
and there to try (if it is possible) to unblock it?
I have W207 with defect radar, so I check on EPC and it shows some numbers:
A0009057405 and A0009057502
I baught A0009057405 and supplier gave me A0009052504, which is same HW,
but different from the original of the car A0009057502
When I am trying to flash it, it reject, and also by xentry it shows like no commincatiom, but it can show the HW and SW (SW not flashed at all).
I purchased a Launch Pad V about a year ago from amazon and the seller was LAUNCH Store. I know launch has added Nissan SGW unlock to North America. I do not have that option on my Launch. I have Autoauth subscription and it works well with Chrysler but for Nissan I do not get the popup to enter Authauth ID and password. I'm assuming it's because I did not buy from launch dealer but from amazon which was a fake store. Is there any way to enable this feature in the tool?
Much appreciated if anyone can give me some insight
I am looking for the ic chips that need to be read for me to clone 2020 mazda miata bcm or a wiring schematic for me to read bcm on bench help will be greatly appreciated thanks!!!!!!
Hello everyone
I would appreciate the help with a DTC delete for a bmw x3 e83 ms45
The codes are 2722 , 271A
Thank you
(02-11-2025, 08:15 AM)kihh Wrote: Hello everyone
I would appreciate the help with a DTC delete for a bmw x3 e83 ms45
The codes are 2722 , 271A
Thank you
trying to replace a pcm, performing the pcm replacement routine, witech is asking for a 4 digit pin. I was able to generate the 5 digit pin from the rf hub, but it will not transfer the secret keys from the rf hub to the pcm without this pin. Can somebody generate a pin for me...will pay for a working pin. This has the smart key system
hi guys
i have audi q7 2007
elv is bad, i bought another one same part numbers and same proccessor, i read the original one flash and eep
is this elv just read and write flash and eeprom to clone? or need to modify eep and flash transfer immo data ?
hi guys
i have mercedes gle 2017 350 petrol, and have dtc P2279-a leak was detected in the air system
also the engine has a whistling. when i open the oil cup, no more whistling also i see the engine has high vacuum . so i changed pcv valve ( crankcase valve)
checked the engine for air leak with smoke test and the car has same problem
Can someone please provide me a CL63 (W216) or S63 (W221) AMG with M157 (MED177) software and coding.
ECU is totally dead.
New ECU No. 2789011400.
DAS can't find software.
This is my first real post, and i just wanted to have some pro's look at my map i just made.
Just to be sure and safe.
The boost is increased to around 3200-3400mbar
rail pressure raised to 1700-1800 bar
IQ increased to 650 mg/stroke
vnt/n75 map optimization
drivers wish map to match larger turbo
smoke limiter adjusted
egr and dpf fully deleted
and finaly the dtcs related to egr and dpf removed.
the car has a ts HTD3073BB
cp3 r70
piezo injectors
stage 3 ic
3' downpipe
egr and dpf removed
Pm for pass, not that i dont want to share my map, but i am still not sure how to guys do it in here
![[Image: b49c3965d1bbac31df9c6ab511ee2778.jpg]](https://uploads.tapatalk-cdn.com/20250211/b49c3965d1bbac31df9c6ab511ee2778.jpg)
