I've got an Atego Truck i have coded 2 keys Truck starts after a week or so i got intermittent starting with a code 9963 " no transponder code through engine CAN bus" checked CAN bus system all is well the problem comes and goes away , so can please some one help with Immo Off attached is MR 93c86 & FR 95128 Eeproms
Hi, anybody maybe have readed eeprom and MPC from VW Passat B8 2.0 tdi 190p 2015-2016y, important is just that is 190hp and manual transmission. Ecu number is 04L907309M, engine code DFCA.
This is the situation:
I have a Peugeot 5008 1.5 diesel from 2021.
The adblue system failed, I want to switch adblue off.
The ECU MD1CS003 is encrypted, so I can't change parameters.
The plan:
I want to buy an older, unencrypted MD1CS003 and swap it with the existing one. I want to do immo off and adblue off.
Is possible to sync ecu with dash on the table? I will try sync on the car but outcode in ecu is 000000, I try use different eeprom file but I can go in to sync procedure...
Files in attachment.
help please w176 a180 CDI FBS3 VGS fdct
Car stuck P and N after adaptation failure
Dtc 287c00 I tried to many times, but no success.
I got a car from other workshop,I changed mechatronic. clone the old module,still adaptation failure, can some help me. Correct firmware version for this car,
Thankyou
Need datasest to LED modules.
I have genuine VCP but there is no ATECA datasets to those headlights.
I have tried to upload with (7P5941591AP ATECA and 7P5941591A LEON) but no success - still invalid dataset DTC is present.
THANKS !!!
I swapped my 5 speed gearbox (code JCR) for another but with longer 3th 4th and 5th speed (code KBL) and cruise control doesn't work on there gears
Found some information about gear ratio's, gear tolerances but still i am not able to make that working
Can anybody help me please?
ECU file attached.
I will be very grateful. I have been trying that for 6 months and unsuccesfully.
Like the title suggests, I am looking for the PC Consult 2 software suite, but I am unable to find a working download link, even on MHH Auto.
I have a fleet of 2005 to 2010 UD Trucks, and I am currently in the process of re-building/re-purposing them.
Most of my trucks are UD440s, but I do have the newer Quon generation in my fleet as well. I have Volvo Tech Tool, which works well with the Quons, but I do not have PC Consult 2.
Could you tell me please which software should I use to the Donor TCU with Odis-e? Unfortunately somebody changed the flash on the inside of the donor TCU early and the car don't start with some DTC's.
Hi, I'm looking for any FREE mappack for ECU ME17.2.4 (BMS-MP). This unit comes from my personal motorcycle. I already have a TC1793 dump and would like to make some changes to it. I'm not a professional tuner and I don't earn anything from it, I just do it for myself as my hobby I'd be very grateful if someone would like to help me with this.
Anyone who has done this file with success? Car has no errors on the Adblue system, but they want to get rid of it and be able to disconnect the injector or put a dummy on it in order to stop the adblu use.
Never done anything with these things. Read by PCMflash
Hello. I have a problem with my Vito, it stalls when the engine is cold. When it warms up, everything is OK. There are no engine errors, I replaced the engine controller but it does not help. Still the same... Can anyone help?
Hi Guys, I have a problem with the lamp in the Passat. Odis reports error C 108131 headlight power module.
I bought the AFS 3G0 941 329 module and replacing old module.
This module is not visible, probably because it is not encoded.
Now ODIS reports
1 - U101400 driver incorrectly coded
2 - C1081F1 headlamp power module
3 - C1083F0 Left light static, electrical current coding fault.
I run a car service shop, and we’re looking to expand into ECU programming, IMMO off, noxy,dpf,egr - fix and parameter modifications. We mainly work with trucks (EU) Euro 5/6 and passenger cars from 2000-2018, sometimes newer models, especially from the USA.
Until now, we’ve been handling ECU repairs in trucks by physically removing the unit and sending it to a service shop. Now, I’m looking for a tool to read the file, send it, and write it back independently. Additionally, I need another tool for IMMO and related work.
I have some experience with KESS/K-TAG, but I’m looking for recommendations on what’s best today for starting out:
1. Cheap Chinese clones (ScmPR2, Iprog, MPPS, etc.)
– A budget option, but I’m not convinced. I have experience with car diagnostics, and since we switched to original Launch and Texa Truck tools, I see the value in proper investments.
2. Mid-range tools (KT200II, Formula Flash, Xhorse Multi Prog, Scanmatic 3)
– These seem like a reasonable choice for now, with the option to upgrade later.
3. Top-tier original tools (Flex, KESS V3, Autotuner)
– The best quality but a significant investment.
Considering my budget, option 2 seems like the best way to start, with a future upgrade to 3 if this service becomes profitable.
I'd be very grateful if someone would like to help me with this.
