Hello, I have a problem with my car. I wanted to do maps update as in my second car, so I bought lifetime FSC code on ebay a downloaded latest MOVE Europe Maps. Weird was, that the code was accepted on third attempt. Then it started to read maps. So I left it finished. But next day, after I turn on the engine, there was no audio, no picture on navigation LCD. I've tried to disconnect battery, but with no luck. I tried to check fuses, but no fuse was broken.
My friend helps me to connect it with ISTA-D for diagnostics - he told me that MQST device not responding.
It's a part number 9283527. Is it possible to repair it, it should be software problem...
Or should I buy new unit (used) - this PN, or can I buy unit with DAB radio - 9244417?
If I swap the unit, is it possible to update maps? Is it possible to use unit from different region - USA unit with US maps for Europe and EU maps?
Is VIN of donating car needed? Is it used to pair with maps..?
Can anyone assist with crash data clear on Renault 8201163278 EEPROM ST95160? The Airbag tools available for download seem to be riddled with malware and have not had any luck.
Hello, perhaps someone had similar issue with ford galaxy diesel 2016 years automatic transmission.
I have no crank problem. Customer said what he drived and speed was going down down and stopped.
Now I have low pressure sensor fault P008A-Low Pressure Fuel System Pressure - Too Low.
And no more faults. I run test and it says 3.5bar low pressure pump getting. With this error i thought it can be fuel pump but the problem is that my started doesn't crank.
In engine ecu live data I have starter disable message. Engine and body computers see brake pedal.
Perhaps someone have similar problem?
I have an issue with the OM646 engine. It won't start but the starter is working. I have also the fuel to the injectors but perhaps it won't start. The CDI-ECU says that the synchronisation is good, the pressure in the commonrail is also good.
The 1 injector is right under the Crankshaftsignaal, then the 2, 3 and 4 injector at the bottom.
I have checked with the scope, is someone see something in the picture?
Is it normal the the 1 and 4 injector and 2 and 3 injector firing together? And why is the first firing later than the TDC?
Can someone to check if this ori softwere or not? "cose i cant to do regeneration by opcom, autel, just eror. Please help! Corsa D 2007 Z17DTR Denso ap47
i have a volvo xc90 it has dtc P011300 in ecm car came with intermitted dtc on power pulse i changed the hose from power puls but sporadic the p0113 came up i cant erase it
what i did
-check wiring from ecm to maf sensor (airmass sensor) al seem ok
-i mounted new maf but dtc stays
-i read measure valuas of maf and i see temp is -40 static (connected or disconected same valua the other valuas i see changing
its a denso ecu and the maf sensor i took a denso after market (sorted it out by part number)
any one here who has experience with these ecu s i dont see water damage but i think problem is ecu
CAN SOMEBODY HELP ME GET OUT CGW FROM BOOT MOODE ONLINE?
THE ECU SET WAS CHANGED FROM OTHER WORKSHOP (ECU,EIS,ESL) I CHANGED VIN IN ABS AND AIRBAG AND I TRIED TO CHANGE KM ON CLUSTER WITH VVDI MB, THEN VVDI MB ASKED ME IF I WANT TO INSERT CAN FILTERS, I PRESSED YES AND DURING WRITING THE NOTEBOOK TURNED OFF.
SINCE THEN CAR CANNOT CONNECT WITH DIAGNOSTIC ONLY CGW IS READ WITH OBD.
CAR IS W204 C200 CDI 2007
THANKS IN ADVANCE
I have an Alfa Romeo Mito 1.3JTD with this BSI( 00505181210 116RI-000674 116RA-000021 28177152 ), does someone have a full back-up(flash 70F3379+eeprom 93C86) for a BSI with these part numbers?
I have a 2013 vw Jetta 1.6tdi cayc with no traction control button. im using stagex for the tuning which all went well but ive tried to apply hardcut via:
torque to iq maps
torque limiters
iq limited via map
and none of them make the effect of a hardcut limiter i also cant see where the stationary soft limiter is at.
Hi all,
Just wondering if anybody came across airbag fault on Kia.Faults are
B110200 Low battery voltage intermittent
B162000
Internal fault replace SRS CM
Active
I'm reading a lot about the SRS CM going faulty on them.Are they repairable or can I fit a second hand one? Are they plug in and play or do they have to be programmed.
good morning I have a problem with airbag module 51968381 Fiat 500L 2014. The car had an airbag warning light on and no communication in diagnosis, I removed the ecu and it came out burnt so it is impossible to repair. I found another ecu with the same spare part code and connected it to the car. When performing diagnosis it gives me many problems stored and activates the code B012F-00 exceeding the maximum number of interventions. I connected upa-usb ori to the PC and selected the script of this control unit, first trying to read the burnt one (with a negative result and a voltmeter with very high values as if there was a short circuit), then I connected the good one and starting reading and after reading in script it comes out (crash detect), I try to do clear crash but nothing changes, it always tells me that there is a crash inside. Has anyone ever had this experience? Maybe by reading ecu in short circuit the upa-usb has become corrupted?
Notice: This platform need work with ACDP Module 37 together
Yanhua ACDP/ACDP2 with Module 37 can correct the mileage for the MB HU6 instrument module (A167/ A213 / A247) equipped with the R7F701403 chip. However, previously, it was necessary to install the original HU6 module in the vehicle and perform mileage modification via OBD. Now, Yanhua Tech has released the MB HU6 YH-OBD Platform, eliminating this requirement and enabling direct bench operation for a more convenient and efficient process.
![[Image: 25021017392550231894.jpg]](https://www.eobdtool.co.uk/upload/pro/25021017392550231894.jpg)