Can odis do automatic removing CP from all modules that have CP on (for example GW change will triger many modules in CP state) or i have manualy to remove step by step CP from modules ?
Audi a4 3.0 tdi 2006 edc16cp34 Original Backup needed
HW: 8E0 907 401 AL
SW: 8E0 910 401 p 0020 or 0050
Here is the problem, car came to me already with bad egr delete , map was repaired egr+flaps+dpf+stg1 was done by me.
Car started was driven 1 day all ok, next day customer stopped to put the fuel in and after that car won't start.
No dtc, cranks but no start.
Everything is checked ecu is the problem.
I sent ecu to electronic repair shop and they said ecu is dead injection drivers problem they could not repair it, by new one and clone it.
I did that and same problem with new ecu.
Crank, no start no dtc.
So if someone has ori backup i will be very grateful!
PS
I know that it is software problem, because by chance i had another a4 3.0 that had immo off on his ecu and with that ecu car started.
I did not clone that one because electronic shop told me that my ecu is damaged and i thought simple clone will do the job, and by the time i figured out it is software issue that car was gone.
Hi,
I start thread here because in fact it is not specific brand related - this
heater is used in a lot of cars.
My heater stop working. As i read after 3 time using car for short distance
heater count this as not successful star and block heater.
With elm327 and forscan i use service procedure FFH module reset, it
complete successfully but heater again did not start.
I remove fuse 20A (HEATER) for 5 hours but this also did not help.
I found 1 yellow cable near to battery but it is too "fat" to be cable
for communication. He is next to 2 other red cables - pic in attach.
Car is Mazda 6, year 2007, 143Hp with xenon bulb next to head lamps.
Here are some pics.
And questions are:
1. Is this yellow cable for communication or where must be this cable?
2. Is there option to reset/unblock heater with elm327 and forscan or
i need to use VAG-COM cable and Webasto Thermo Test to do this?
Hi,
I have a problem with a very old car: Mercedes Vito 2.3 TD 1997. Bosch ECU with UV erasable memory B58545 (87C257). My tuner did EGR off + Stage 1, but after writing the file there is no communication with the ECU. After writing the original back it is ok. Probably a checksum correction is needed, but no one knows how to do it. Can anyone help? Ori and moded files in attachment. Thanks in advance!
Hi everyone! Have you encountered a decrease in low rpm thrust when disabling the yerg by nulling the hysteresis? Why does it happen? I've been looking for an answer in the documentation for a long time, but didn't find it. How to deal with it?
Nissan Denso ecu immo off .
I need help to make immo off for nissan SH7058
please i need help if your solution is for sale,please dont reply to my post .
thanks in advance .
Hello
I have a Problem with an Volvo V50 1.6 psa 2007.
ECU Bosch EDC16C34 0281 011 775
4N51-12A650-BB
31211076
Did read out by Kt200 Clone. DPF and AGR has been removed with Swiftec.
After installation of ecu, engine started.
After afew hundred meters engine stopped.. possible to start again.. this happend about 7 times..
Car rested for half day.. then engine doesnt start anymore..still cranking but not running.
flashed back ori files..same.. engine cranking not starting.
only fault i got is in CEM ..Fault code CEM-3A00 ECM Software Wrong signal...and in data Stream of CEM is ,,Immobilizer, ECUmodule check -not ok..
No immo Massage on Dash.
Attached ECU eeprom and Flash
also
CEM eeproms
Numbers in ABS module: ECU Software number 0030667832AA
ECU Hardware serial number 000000077639
ECU Hardware Partnumber 0030742665AA
ECU Diagnosis Partnumber08688027B
Can somebody check Syncronisation and if ecu eeprom or flash are corrupt?
Hi Please help me correct mileage in dump from dash Kia sportage III 2020y Dash with nec D70F3526 and epprom 25c26 same as 95160 Below I upload dump from epprom 25c16 I have 120488km and I must have 112100km
Hi, I'm working on a transit with adblue and dcu17pc43, engine is in no-start mode due the distance counter reached 0. Currently trying to do an adblue reset but it's not working. Tested launch x431 and Forscan, none could make it start, looking for an advice or what can be done to make the enigne start.
hi please help peugeot 807 2.0 hdi 2004, remote only make blinking lights and dont lock or unlock doors. i think someone remove immo and after that remote never close or open doors again. i try with delphi and cant program with security code with lexia dont have can line so dont detect ecu or bsi but car works fine and all except doors lock work.
anyone had same problem?
