hello. i have been looking for workshop manuals, wiring diagram all relevent information regarding this busses
we have 10 of them and 2 of them have automatic transmisson problems and i cant find any information
the gearbox is GAV781R
i have checked on Scania multi and there is no information to be found there
will pay if anyone have complete workshop manuals for this
Hi! I have tried DPF and EGR off with Davinci , it doesnt work ... no dtc's but blue smoke is still there . i believe dpf regen switch has to be switched off , but dont know where to find it. Attached the files , one of them is clean one only with stage 1 tune on it , another one is Davinci corrected. I can pay for working solution . Thanks
i have an issue im trying and im trying to get the ( start diagnosis) button to work but it wont work for me and if i change it to
Component diagnosis it says that im running a test mode.
can anyone help me get passt this,
also im using a VAS6154 Clone do i need anything else i just want to be able to clear my Component protection so i can use my radio again,
im using Odis-s 24.1.2 and win11
please help
Hello
Have strange issue with immo audi A6 C6
Original Eeprom car starts and cutsoff
tried V1 and V2 own solutions but V1 cranks only
V2 cutsoff same as immo on
V3 car starts but its too much damaged areas in immo and rest, car doesnt runs correctly, shaking and fueling trying to cut off 4mg to 0mg i 1sec, railpressure sensor disconnected keeping stable fuel inj. but cutting at revs at 2000rpm
Hello everyone, I have the diagnosis for Kia and Hyundai in the American market but when I try to install it I get a 404 server error. Does anyone know why and how to fix it?
IF ANYONE WANTS THE SOFTWARE, PLEASE WRITE TO ME AND I WILL BE GLAD TO SEND IT TO YOU. I DON'T WANT TO PUT THE DOWNLOAD LINK SO AS NOT TO HAVE PROBLEMS WITH MEGA
Hello!
I am looking around for a way to enable an additional high beam output from the front sam, in this case on a facelift W204. Also where to wire the signal (which pin on the front sam) would be nice if anybody knows.
I know this should be possible since there is the equipment code 83O, ACTIVATION OF ADDITIONAL HIGH BEAM HEADLAMPS.
I have been looking around at the coding from the SAMF_172 but I am not totally sure which it could be. I believe it should be in this block: 14.VCD_Parameter_Fernlicht.
Here is the coding currently from the car, if anybody knows or could help it would be deeply appreciated!
Fragments Values
FL_PWM_disable nicht aktiv 04CV
Fernlicht_Einschaltverzögerung 0 sek 04F7
Fernlicht_Fehler1 aktiv 04CA
Fernlicht_Fehler2 aktiv 04CC
Fernlicht_Fehler3 aktiv 04CE
Fernlicht_Fehler4 aktiv 04CG
Fernlicht_Lampenspannung 13,1 V 04F2
Fernlicht_OK ja 04CM
Fernlicht_OpenLoad_links 0,52 A 04FL
Fernlicht_OpenLoad_rechts 0,52 A 04FV
Fernlicht_ShortCircuit_links 8,5 A 04FG
Fernlicht_ShortCircuit_rechts 8,5 A 04FP
Fernlichtausgang über LAM-Steuergerät deaktiviert 04CT
LAM_NV_IR_15 nicht aktiv 04CX
No_H7_Spot ja 04CK
OpenLoad_Erkennung(3) nein 04CH
PLSM_HiBmStatv2OffDelay 0,2 sek 04GL
PLSM_TIHC_NSL_HiBmOff 7 sek 04H9
Taktung(3) nein 04CR
Treiber_Ein nein 04CN
Xenon_Fernlicht_OpenLoad_links 2,24 A 04G4
Xenon_Fernlicht_OpenLoad_rechts 2,24 A 04GC
Xenon_Fernlicht_ShortCircuit_links 10,0 A 04G0
Xenon_Fernlicht_ShortCircuit_rechts 10,0 A 04G8
Hey do anyone here know what tool/equipment Nevs uses for their Saab models? Tech2 only works up to 2012, tested it with CANdi box on a Nevs Saab 9-3 2014 and dosent work. And the engine is a Opel engine.
Any ideas? Would be good to have for coding etc like we do with Tech2 very often.
Thanks for anser!
![[Image: DTXOFFLOGNUP.png]](https://i.ibb.co/ZG9CzMK/DTXOFFLOGNUP.png)
![[Image: DTXOFFLOGNUP2.png]](https://i.ibb.co/VvNS6pr/DTXOFFLOGNUP2.png)
![[Image: OFFLOG.png]](https://i.ibb.co/qWHGTGk/OFFLOG.png)
![[Image: Rate.png]](https://i.ibb.co/5MTRbXf/Rate.png){kind=small}
![[Image: Thanks.png]](https://i.ibb.co/JK8DZ1B/Thanks.png){kind=small}
