Hello, I have a vts activation problem in the front bcm after having connected a rear bcm from another vehicle. Now the vehicle won't start. The rear becm is new original and CS and VIN have been passed from front to rear bcm by dump. Attached rear bcm dump 1m12s virgin and adapted, damaged original 3m25j rear bcm dump, front bcm dump. Could someone help me delete vts by dumping front bcm?
Fault bcm front
805208 Rear end electronics, confirmation failed
80530F Re-start inhibited by VTS
C12017 No Communication With Rear End Electronics Control Unit
Hi to ALL, have an Peugeot 5008 1.5hdi.
The Software was modified by someone, and the car is acting very strange.
Can someone please help with stock Firmware?
Thanks in Advance !
Hi,
I have a problem with PL menu programming in LCN1 from Nissan Juke.
I made a few PL menu installations in LCN1 units, usually from Qashqai, never had problems. But in this one, when I put SDcard into the slot, I get info
"Download Media Found" I can see version dates, like usual, but I can only click Cancel, Update is greyed out. Anybody had similar issue with those units ?
Hi, i have renault modus form 2005. With power steering problem. The car says internal electrical fault with the original power steering module. I bougt another car dont have fault in eps but immo in the UCH is on. I transferd eeprom dump from the old to the new module. Car starts but still no power steering. And the internal electrical fualt came back. Its saved in the old eeprom. Both EPS moduls have the fillowing partnumber 8200433516. can you please see what is the best soloution? Either repair the old file or viginize the new file. i will attach both files for you. And im willing to pay. But only for a working soloution.
hello
i have
Audi A4 2.0 Ecu edc17cp17
engine code CAGA. 143 HP
this car with automatic transmission has been modified to manual transmission.
so the bva fault lies in the engine ecu dtc.
its hw ori 03L906022B
LONG CODING 0104000202072020.
I want to reflash this ecu with a flash from another with manual transmission.
what can you advise me
with immo off
or without immo off
which path to choose
Thanks
I need a full bench read of Sprinter EDC17CP57 ECU,
I had someone made a bad map file now ECU will not respond via OBD only VIA Bench read... Bench Flash and OBD Read is same size but when I lead OBD backup using bench connection ECU Still not respond over OBD connection....
Hi
Can anyone help with immo off solution for Kia Ceed 2009
HW 0261S04357
SW 1037377897
The few instructions online i found say to go to address AC070 and edit the byte from AF01 to AF25 to immo off
I have a similar string showing at AC060
My binary in the right image is slightly different starting at AF00,
Will the above solution work, some pointers or help would be fantastic
Thank you
MPC + EPR attached
Hello, friends!
I have a win11 24H2
I installed the Caterpillar program, but at startup it does not see the license in the FLEXlm folder, although the variable is registered... Maybe you need to remove some WIndows update?
Ciao a tutti, qualcuno è così gentile da vedere se dpf off in questo file è corretto? c'è anche egr off dal singolo bit e un leggero aumento dei limitatori di coppia ma non importa.
---How do I attach files? What format does the forum accept?
Ich brauche Hilfe bei der Identifizierung eines Steuergerätes aus einem Dodge Ram 5.7 Hemi.
Leider ist es kein GPEC2A. Außerdem passen die Bilder nicht zu einem GPEC4 oder GPEC4LM
I have Renault Megane II 1.5 DCI 106HP SIEMENS SID301
HW: 8200495479 SW: 8200542288 SW upg.: 8200557608
I would need an EGR OFF but also I would like to do stage 1.
I have a mappack with main maps like DW+TL+Smoke+Nm2IQ and Overheating limit+Turbo maps and Rail maps but I'm not sure it is enough for Stage1 tune.
Can somebody help for me. Mostly EGR OFF solution is the priority
![[Image: E1n5vd1.png]](https://i.imgur.com/E1n5vd1.png)
