Helping a buddy with an engine swap get his car running, MED17.1.1. It is a 4.0T swapped into an older car. In his State he needs the VIN and Mileage to match for emissions inspections. I adjusted mileage, VIN and IMMO and the car starts up perfect. The problem is there is no throttle response at all and the engine has a lumpy idle.
He sent it back to me to look at it again so I put the ECU in my car to test, and I get the same response. Starts up perfect, lumpy idle, no throttle response. I changed powerclass as well, issue remains.
I have tried a few different versions, even rolling it back to only changing the IMMO and I get the same result. I am pretty new to ECU's, not sure what I should be looking for here. Any help is appreciated. Files attached. Both are checksum corrected.
I'm Offering Limited time FREE Dodge Jeep GPEC3 FPEC4 ECU Unlock until 25-jan-2025
send me bin file on private message you must mention ecu type GPEC3 Or GPEC4
I will unlockit and send it back to you via private message
[font="MHH Font", Calibri, sans-serif]'m offring free unlock for limited time for Dodge & jeep ECu's [/font][font="MHH Font", Calibri, sans-serif]GPEC4[/font][font="MHH Font", Calibri, sans-serif] and GPEC3 only[/font] [font="MHH Font", Calibri, sans-serif]Send me flash bin file to me in Private message "You should mention computer type" i will unlock it and send it back to you[/font]
[font="MHH Font", Calibri, sans-serif]Hurry Hurry it's a limited offer[/font]
Hello!
I also have a problem related to a UCH Scenic 2 from 2008 with Keyless go.
With Renault Pin Extractor I can't find the PIN code.
I found the ISK code with CanClip but when I want to find the PIN code with Renault Pin Extractor it tells me "Invalid ISK Code"
I also tried with RenoLink, it finds a PIN code but I don't know if it's correct because after I connect in RenoLink after 3-4 seconds it disconnects.
If I quickly click on "Start Learning" I get the message: "7F3B22 Conditions not set or sequence error"
This is one reason why I don't know if the code is calculated correctly by RenoLink plus it can't be calculated with Renault Pin Extractor.
The ISK code is read correctly because in CanClip it's the same code as in RenoLink.
The ISK code is 85 95 3E 67 EA 82
Please can someone help me with a correct PIN code because I want to program another card to have a spare because the car came with only one card. I will do the programming with CanClip but I need the correct PIN code.
Thank you.
I bought a used ecu after an ecu fault and
I cloned the eeprom, deleted the immot, there is no more sart error, the car starts, but does not start.
If I cloned the eeprom, should I start or do I still need to teach?
I did the cloning by connecting directly to the eeprom with a CH341A Programmer
I deleted the immo from eeprom and under of68. according to description
Hi, I got one broken AmtBst clone and my guess is that I got problem with firmware. I tried to resolder every chip and do some inspection on board but without luck. I got AmtBst driver in Device Manager but no device found when I try to run app.
Btw everything works just fine till I click on update app.
Can someone share firmware for that or some solution how to fix it. It's not hardware issue, it's just software issue.
Hello all ..
would you help me to solve this problem :
i have skoda kodiaq TDI with dq500 transmition, when i park it for long time more than one hour then start again and go it takes long time to engage the gear even it show on dashboard D1 and no fault code on TCU
i replace the mechatronic
i replace TCU (but same clutch postion sensors)
i replace the all gearbox
but still the same problem
Hello, me7.5 after flashing mpps v18 car dont start. I was try read full system Foxflash but i have error. In boot mode its only flash. Does anyone have an idea how to set this up? I have a flex too. I have already ordered it for the future, ktag but I need to revive it ASAP
Has anyone ever faced issue during connecting with car that Firmware is running abnormally... I tried the Firmware fix but doesn't work at all. :/ any idea please? It was working well till end of 2024...
Hi guys.
I own a A3 Rs and there is a software on the ECU . I suspect the software is faulty so i want to read it and send it in for verification. I have a KT200 II but i cannot get connection to the ECU on Bench mode with it. Is it possible to read/write this ECU with KT200 II? I am new to this matter so be patient with me.
thank you
Hey Everyone,
I am looking for someone to help me out to see what options I can enable on my own car which is X253.
I am particularly interested in Distronic Pro or Plus. I have all the cameras in front including augmeneted reality one and the speed limit recognition is enabled already. I do not have 360 cameras. I do have collision prevention assist so the question is for Distronic Pro do I need to swap the radar? I know I need to order the buttons for the steering wheel.
I am not looking particularly for a free solution.
Hello everybody,
has anyone used (tested) the OBD cable (PN: 1684465881) listed below with BOSCH VCI C6 MTS-6532?
Is it mayby compatible with the XENTRY Diagnosis VCI device?
Thanks for any possible information!
Hi! i have an 2009 a4 b8 with B&O amlifier with 95256 eep and i want to replace with ASK with 24c64 eep, i need to transfer CP, amplifier works onliy mono because of component protection active.
in ASK amp location lor cp is from 3E0 to 4AF but in B&O i do not know where is it and how to transfer
Maybe someone can help!
i am wiling to pay for working solution
Anyone can make this file Ori? i think there is problem on file (client bought car with problem);
car have no power, i think problem is on file; because no dtc but limp mode and Engine lamp on.....please i would to restore ori this file, and try.....
![[Image: 002.png]](https://i.ibb.co/KWmZ8rh/002.png)
![[Image: 003.png]](https://i.ibb.co/HXtFx6t/003.png)
![[Image: 004.png]](https://i.ibb.co/hHBCn8j/004.png)
![[Image: 005.png]](https://i.ibb.co/s39RzKp/005.png)
