Anyone can make this file Ori? i think there is problem on file (client bought car with problem);
car have no power, i think problem is on file; because no dtc but limp mode and Engine lamp on.....please i would to restore ori this file, and try.....
I m looking for developer partners of diagnostic for this car / attached example engine ecu
current diag system under server,and server have problem in this days
in garage have some cars not working after accident
Hello Folks,
New A200 sedan delivered this year.
The title phenomenon occurred 10 times a month in ECO mode.
Missing gear? Gear spinoff? I do not know how to explain the phenomenon.
Anyway, gear suddenly becomes neutral while driving from D to N without touching the gear column with walking speed to 50km/h in Eco mode ( no occurred Comfort mode ).
Dealer explain that MB is currently creating new software.
Does anyone have the same experience or any solution?
hi,
I am working on a 2013 Mazda 6 with a 2.2 diesel engine.
The client wants stage 1.
how many horsepower can be put and a price please.I read the kt200 tab
hello
A colleague can help me with verification only, if the immo off is done well. I don't have a car, they only have ecu.
Thank you,
vw golf 4 036 906 034 BB Magneti marelli IAW4LV.H eeprom 95080.
Hello !
Need 100% IMMO OFF Mazda 5, Petrol, 2005year
ECU Mitsubishi: E6T53975H1 , LFD7 18 881C
I need a tested and 100% working solution--- of course i will pay for this !
Hello,
I would need an egr off for denso opel zafira, 100% functional please.
egr blocked with a valve and disconnect.
and dtc off P0400 P0409
thank you very much
I have a wifi connection problem with SD connect C4 DOIP (clone) device.
I used it for a while with wifi without any problems.
During wifi connection, the message "Could not connect to this network" appears.
This problem never happens on my computer with Broadcom wifi card. It definitely happens on computers with atheros cards. The operating system is win10.
Hi,
Does anyone have any suggestion on what tool I could use on mileage correction the ecu is med17.5.21 ,
Don’t have the budget for a dashcoder 4 been looking around can’t find much been told Super DSP3 might be able to do it.
Any help is appreciated
Hello everybody
w212 facelift with huge battery drain come - morw than 5Amps .. start looking at problem and see strange sound in trunk when lock car and wait 5-6minutes . Sound gots from rear sam module and it likes relay clicks inside. When remove all relays and fuses there again this sound. I purchase brand new sam module - i do personalization and scn - all looking perfect , no sounds , no drain , but fter 3-4hours car start flashing all rear lights , and licence plate light too and again sound this relay clikering …… what happened ??? please any ideas
My W221 Mercedes-Benz recently developed an issue with the head unit (Comand). The screen intermittently blinks black, seemingly losing power, and simultaneously, the dashboard clock resets itself. I ran Star Diagnosis on the car but found no specific faults listed under 'COMAND'. A friend suggested checking the connection to the module located behind a panel in the trunk on the left side, and inspecting for any signs of water or moisture. They also recommended examining the auxiliary small battery. Is this the correct approach, or are there other areas I should investigate? I appreciate any insights or advice you can share. Thank you for reading.
Hello everyone
I have big problem with mercedes gl w166 - on dash have blind spot inoperative , pre safe inoperative. I do short test with xentry and cannot see a90 there. I remove radar in front bumper and with multimeter see there have 0V with if igniton on. Open a wiring diagrahm and see i must look at rear fuse box for fuse 116 - 5A. There i see a blown fuse , but when replace it blown again. I disconect radar and socket to radar - put new fuse again and measure to radar wiring 12v but but but …. dashboard gone CRAZY!?!? any start to blink in red - no ecu , no start engine , no transmision - fuse not blown again - but all is removed and i dont understand what happen… when i remove f166 all is okey - when put car goes crazy again. please help
Hello, I solved the problems of the cam sensor in the 1.6 TDI. is it possible that the problem was in the contact of the frame cable, i.e. the brown one, with the motor frame? the cables lead to the motor unit, so the power supply and the chassis are somehow shielded? or the fact that it rubs against the engine block should not cause a malfunction
THIS SITE https://www.stage-ecu.com/ OR AS THEY CALLED THEM SELFS STAGE ECU WORLD , SELL CRACKED SOFTWARE OF WHICH MOST OF IT YOU CAN FIND FREE HERE , BUT THEY CLAIM TO HAVE SOME SOFTWARE AND THEY SELL IT AND THEN IT DOESENT WORK AND THEY BLOCKED YOU FROM THEIR SITE AND MESSANGER !!
FIRST THEY CLAIM THEY ACCEPT PAYPAL BUT WHEN YOU ARE WILLING TO PAY THEN THEY TRICKED YOU THAT IS NOT SUPPORTED AT THE MOMENT !
ALSO THEY SELL YOU SOFT 140 GB AND WHEN DOWNLOAD STARTS THEY LIMIT YOUR SPPEED TO DOWNLOAD SO YOU CANT DOWNLOAD IT IN A 10 DAYS ! BUT IF YOU PAY 70 EUR MORE THEY LIFT THE DOWNLOAD SPEED ! AND AFTER YOU DOWNLOAD IT THE PROGRAM DONT WORK !!! AND THEY STOP COMMUNICATE WITH YOU AND BLOCK YOU !
Hallo, Can someone confirm please if is possible to install used steering lock module or must be new (virgin) I have installed used module and done ID certification via Techstream but car not start-steering locked, error B2288
hi
I clone bcm for ford ranger 2015
everything is good ,the car is started correct but
in dashboard the mile is not afiched , just "- - - - - - - -"
my question is whin I cloned it the mcu motorolla MC9S12XEP768 FOR SECURED AND UNSECURED there are 4 parts d flash, EEE, pflash, and pof
the part EEE can readed , but c'ant writed, evry one asked ,say the EEE is parts from D-flash , I accepted and resize dflash and write ,but evry time the sam no chenge in EEE
please any solution
