Hello, after replacing the airbag module in a Renault Master 2021, I have a problem with coding. I entered the chassis number (vin) into the blank module, I only have errors related to the passenger airbag and the airbag switch, this car does not have these elements. How can I decode them? it has renolink, ddt4all, lunch, etc. unfortunately I can't deal with it.
a friend of mine got himself access to Xentry Pass Thru through Daimler (yes, he did). Apart from the installation they require him to unlock several URLs and Ports in the local / network firewall / proxy. Since I am not too familiar with that, how does one do that?
The backend-server cannot reach mercedes-benz.de (port 80) and xentry tips (port 443). Can someone please tell me where and how to unlock these in Windows 10?
Hello I have problems with rear bcm on Jaguar XF 2013 , emergency lamps always on , stop lamps too , and when push brake pedal open trunk , I have readed bcm , please for repair my files , readed by vvdiprog
Hello, i have problem with getting eeprom or only pass for 220 EIS with 1J35D chip. I connected all wires to vvdi prog but what i read is not full data so VVDI MB dont want it to load, saying that this is unsupported file format. I Can read EIS from cable in vvdimb but IR not work, so need pass to copy all data to the new eis that i buyed.
What is going on?
Attaching also photos of connection. Using mcu reflash cable v3, second use from new. Nothing modified all stock
Hi,
I have problem with MIB2 from A4 2016.
After update to MHI2_ER_AUG22_K2161_MU1421 (from p2133 sw version) All working ok.
Installed MIB tool 3.7.1 but it cant do patching.
I try downgrade M.I.B. tool to 3.6 and that`s my very bad idea- it stuck!
Instaling MIB tool form red menu ofc.
Now it stuck in "SW update" red menu and only info in middle of scren with something like "Initalizing installation program, plesae wait" And rebooting after 5-6minutes and starts again.
After about 3-4times it went blank screen.
When try to reboot manual, it repeat proces from "initializing..." and still the same.
Is the only way to recovery or stop install ("MIB tool" what stuck) is to connect putty ?
Hi. Don't register or buy anithing from this site https://www.stage-ecu.com/
It is a fraud. Be carful.
Don't buy.
(01-16-2025, 01:27 AM)Nauto Wrote: Hi. Don't register or buy anithing from this site https://www.stage-ecu.com/
It is a fraud. Be carful.
Don't buy.
Payed for order and no sofware. Order 4307 and after not working they just canceled on site. No anser from watsapp or mesanger. Just bloked me. That's why they don't have payment by paypal. I'ts a fraude. Don't buy anithyng
Hello everyone need ori dump file for this ECU, i think that my Flash or eeprom are corrupted .
EDC17C60 Peugeot 3008
Part numb. Bosch 0281034189
HW:9806460480
SW:9692929080
Regards,
Fabio Santos
I used EDC16eeprom calculator to make immo off to this seat leon with EDC16U34, car now starts all OK, but it has check engine and glowplug light blinking, and the following dtcs in the engine ecu: P1640 + P0610
anyone can help with this? is the immo off incorrectly done? or I have to disable the DTCs in flash ?
attached ori eeprom and immo off one, files are read with hexprog in bench mode
Hi!
I`m looking for software - TDC2 CALCULATOR by DRIVEABILITYGUYS
It has been posted here by a member, talk with the guy but it say that it forget the password for archive. If anyone have that app I will really appreciate to share with me.
For sale, approximately 100 car instruments. Some are complete, while others are incomplete.
Types include: Golf V, Mercedes W211, Focus MK2, Mondeo MK4, Fiesta, Megane, Audi, etc.
The whole lot for 300 Euro (3 Euro/piece).
I would like to sell it all together.
If interested, please send a message.
