Hi fellow members i have hino n04c with dpf problem , tried other soloution but truck wont rev over 2500 rpm with mod file.can someone please help me with a working dpf off soloution
Hi Lads i looking help fix cas 3+ or change km in CAS org 267 xxx km need 203 678 km after change i get fault with ista about km confius betwen dash also ista show over 524 xxx km possible have look dump i make this km with vvdi2 i would like add before i tryy do this by obd2 with vvdi2 and vvdi 2 update flash like for make new key by obd but after thath not poosible make km by obd2 woith vvdi2 get error .
Hello. I have 2011 Insignia 2.0 CDTI EcoFlex which has a "Service Suspension System" Error on the dash. From what I have researched I cannot read those errors and the suspension module with the Chinese clone of the OP-COME because the communication is done through CH-CAN. I have tried several shops with different scan tools and in only one with original GM MDI were able to read the error (one of the suspension sensors or the wiring causes the problem). I want to be able to read those kind of errors and modules by myself so I am searching for a tool that I can do that with. So the questions are - Are the original OP-COM and original GM MDI are the only tools that can communicate with this module? Or I can buy GM MDI clone (and from where) or something like THINKGDIAG 2. Or there is even cheaper alternative?
2021 Mercedes w167 gle450
Car no accidents
This morning can’t start because of 48 volt battery problems Please if anyone has expeirence in repairing or solving the issue, for my car problems
Faults are there :
B183349 the battery for 48V onboard electrical system has malfunction. There is internal electrical fault.
B183371 the battery for 48V onboard electrical system has malfunction. The actuator is blocked The actuator is blocked
Heya all,
I have an ODO.correction to do on a 2019 Nissan NV350 Caravan.
I haven't seen the vehicle yet, what eep chip is it?
I have
VVDI prog
I-Prog
X-prog old version
Carprog
Digiprog 4.94
I got an altima with deployed airbags and i have to clear the crash code, but the problem is that there is 2 eeproms (93c56) which is the one i have to read or how do identify which is the one with the data? (I am new to this)
Hi guys, I have an older MDI 1 clone that I am trying to get running as a backup. It will not boot and recovery in the MDI software fails.
Is there a raw dump of the sd card available or any tips or tricks for getting it running?
I have a real MDI device as well, if I do a raw copy of that onto the sd card in the clone will it work as long as they are both not in use at the same time?
I am also comfortable setting up a serial rs232 to the device if need be to reflash.
Hello, I have a query regarding activating cruise control via Diagbox telecoding for a Peugeot 208 1.6 VTi. Naturally the feature is not available as standard or an option in my country, but I've seen on YouTube that it can be activated.
Thing is, although I do notice the option on the BSI module, I can't seem to access my ECU. When I tried to access the ECU on Diagbox it just goes blank, not even having the "Repair" function appearing. Since I've bought a Lexia cable from AliExpress, I'm wondering if my cable just can't access the ECU, or is there something with the Diagbox that is not allowing me access? Can anybody advise on this? Thanks!
Hello everybody, i´m looking for the correct fixes to make [font="MHH Font", Calibri, sans-serif]Daimler Truck Platform Independent Diagnostics [/font]work.
If anyone can help i´ll be very thankful.
I don't care wich version, any version will be ok.
I have read MS41 on bench with Kess.
Have done immo off. But need to be checksummed.
Is it ok to write this solution? Kess says it has checksum error. Thought it calculated it.
Hello, by using Xentry i have read out these fault codes but i would like to know what you guys think they mean?
I do kind of know about the fault interlock because the dealer told me the webasto would occasionally lock itself, but how do i remove this?
I also have intermittent starting issues as stated by the fault code, the car will crank fast (or maybe sort of click) and nothing happens.
I can cycle sometimes 2 times or 7 times before it starts.
When Xentry was connected i read 11.7 volts with the ignition on, maybe that is too low and indicative of dead battery?
Hello! I am glad to be part of this nice community, as for that, i am going to offer you a free single stage 1 for diesel/user without other solutions. If there is any ecu that i will not be able to do it , i will tell you. Bring me up those diesels
Hello everyone! I have very strange case with W212 from 2009 and it's Steering Column Control Module. It has 2 fault codes on the SCCM212 module - Lane Keeping Assist has a malfunction and The DIRECT SELECT lever has a malfunction. The interesting part is the the SCCM is not equipped with Direct Select Lever nor the car has Lane Keeping Assist. What I am thinking is wrong flashware because SCCM doesn't have variant coding. Steering wheel seems to not be original but from W212 facelift but I am pretty confident the steering wheel won't make this big difference... Has anybody witnessed similar issue?
