Hello, I updated the car modules and I can no longer connect to the OBD. It's a BMW E92. At the end of the update, it made me unplug the chia from the ignition and since then I've lost the connection with the car and I can't restore it. I used a D-KAN cable and insta/p. I use an ICOM emulator. The ignition won't turn on, absolutely nothing works on it, it's like it has no power, only the failures work.Is there any way I can rewrite or restore factory settings for CAS if I don't have an OBD connection? Thank you!
Greetings to all the masters
Mercedes w470 2018, there is a block from Nissan
I did not find eeprom inside, I read the processor r7f7010643 thinking that there is an accident in the processor (but I am not sure)
Who can remove the accident?
hello,
in need for adblue off for mazda cx5 shmr. i managed to do it in scr ecu, adblue 100% but km still going down. i need also ecu solution, read file attached. thanks
[font="Segoe UI Historic", "Segoe UI", Helvetica, Arial, sans-serif]Hello, I have a Clio IV AKL I have programmed one card to put the ignition on it cranks for 5 sec and that is it. I have a problem with the ecu(Valeo V50) saying it is protected.[/font] [font="Segoe UI Historic", "Segoe UI", Helvetica, Arial, sans-serif]How can I remove the protection I dont have a Clip but i do have rentool, a version of renOlink, And an autel im508. [/font] [font="Segoe UI Historic", "Segoe UI", Helvetica, Arial, sans-serif]Thank you in advance[/font] [font="Segoe UI Historic", "Segoe UI", Helvetica, Arial, sans-serif]David[/font]
Hi I bought a set of injectors but can't seem to code them because the car wants 6 digit IMA but the injectors are 7 digit IMA.
Can anyone here convert them? I'm willing to pay.
old injectors = 0445110131
new injectors = 0445110219
I'm still waiting for the new Mercedes Airbag to arrive, so I decided to get a used one in the meantime. I know I need to re-program it, but how is this achieved? Can it be done just via Xentry?
A few days ago i try to make me with a EGR OFF file, which closed the EGR completely, now the regenerations do not get the correct temperature. Someone could help me, as I have read you have to leave some EGR map for this to work correctly.
Can someone help me?
It´s for a BMW 320d LCI edc17C50
attrached orginal map.
Hello everyone, I have a Fiat Doblo from 2006. The customer stated that the car does not close. My diagnosis so far is that the car does not see that both the rear sliding doors are closed. My question is, how can I simulate that the doors are closed, and that no type of voltage reaches the door connectors? Could someone help me with an electrical diagram or tell me where this voltage comes from? Thanks in advance and best regards.
Hello everyone,
Can someone help me to do a DTC OFF and on a DCM 3.5 Fiat Scudo 2016.
I tried with some software "DPF EGR Lambda Remover" it doesn't work.
Is it possible to do an off on the DPF fluid only?
The DPF itself I want to keep it.
Here are DTC's to do OFF :
P0686
P0488
P1498
+ the DPF fluid circuit ( pump etc..)
![[Image: 54264260978_65ddf87a01_z.jpg]](https://live.staticflickr.com/65535/54264260978_65ddf87a01_z.jpg)
![[Image: smile.png]](http://www.digital-kaos.co.uk/forums/images/smilies/smile.png)
![[Image: error.jpg]](https://i.ibb.co/CJpfvd7/error.jpg)
