I'm looking for someone who has successfully done pops at sport and sport+ mode in MB Med17.7.3.1, so I found the ignition maps from sport and sport+ modes, and I also found the dynamisc fuel cut map, but I can't find the switch and the stationary fuel cut.
Ofc, the schubabschaltung is coded by monaco.
KFTVSA and WMN/WMNST working but there is only a one or two pops.
The problem is that the ECU does not communicate via OBD (flasher or diag). Via bench or boot no problem - KESS3, FLEX. I tried to clone another ECU and after cloning, the unit behaves the same (with ori stage of the donor unit, it communicates via obd but immo blocked of course). So I am suspecting problem in SW (maybe bad flashing).
Can someone find original in his database?
If someone wants to check the files, backup is attached (I can only check mpc).
purchased doip kit for my c4, changed eeprom, soldered connector, all good but it wont connect on LAN to laptop.
Finded that crystal is missing on doip kit, is there someone who can read me value from it?
Hi, we've ran into a problem with diagnosing renault Megane IV with 1.2 tCe (H5F408). Car throws P0420 code witch means catalityc converter problem - I checked emmisions and car passed emissons good, but readings on B1S2 are looking like catalityc converter is bad. What is very important here car doesnt show reading from B1S1 nowhere - I can't see data from this sensor, measuring blocks shows always 0mV - when I unplug sensor it shows only code from lambda heater but not from sensor itself.
I put endoscope in catalityc converter and it was cracked, and dust from it was everywhere, so we replaced it with new one, but it doesn't fix issue with P0420 and B1S2 readings. I don't know where to go from this point, I think this is related to B1S1 not showing any reading but im sure sensor is good, but problem is within ecu, not sure if software or hardware related. I've found on some polish shites few pepople with identical sympthomps, but no one managed to finish his story.
hi , i changed the abs pump in golf 6 2.0 tdi 2009 now i need coding
there is no cruise control no tpms nothing extra installed
vag number 1ko 907 379 CD esp mk60ec1 vin WVWZZZ1KZ9W538206
VCDS SCREEN IS ATTACHED I GOT FREE ESP CALCULATOR BUT THERE IS NO 1KO 907 379 CD IJ THE LIST
SOMEONE IF COULD PLEASE CALCULATE CODE OR GIVE E CALCULATOR THAT SUPPORT THIS MODEL ?
Hello, I have now VW SHARAN 2.0TDI BLUEMOTION, but this ecu is damaged and i cant read with flex, kt200ii
So what now?
Can I buy used ecu? But what support ecus? because I cant find 03l906018G.
Can I buy 03L906018HK write origo file and immo off?
Vident iSmartDiag 510 PRO with comperhensive diagnostic functions, clear and advanced photograph, Bi-directional component test and components calibration, works on mobile phone and tablet with Android, iOS operation system.
Why choose VIDENT ISMARTDIAG510pro:
1. Complete capabilities for read/erase fault codes, live data, freeze frame, active tests, ECU information for all vehicle systems
2. OEM-specific coverage for over 110 American, European and Asian makes from 1996 to 2022 (some makes to 2023)
3. Automatic VIN identification for easy vehicle communication
4. System Detection – detects only the systems that are specific to your vehicle and reads for errors, meaning you haven’t got to spend time looking through data that might not be relevant
5. One-Touch Full Vehicle Code Scan & Clear quickly checks and clears codes for all available modules on the vehicle
6. Ability to record all available live data parameters and graph any four on screen at once
7. Support CAN FD, DoIP communication protocols, don't need extra adapters to diagnosis.
8. Direct Access to the most common required special functions such as oil service, EPB, DPF regeneration, throttle body alignment, steering angle sensor calibration, battery configuration, etc.
9. Comprehensive data manager that can store thousands of vehicle records, customer data,vehicle IDs, fault codes, repair notes and diagnostic results
10. Interactive Data Logging sessions enable direct contact with Vident Technical Support for first-hand bugs troubleshooting
11. Life free update
VIDENT ISMARTDIAG510pro Functions:
1. OE-Level ALL Systems Diagnostics 2. Bi-Directional Test
3. Full OBD2 Functions
4. Support CAN FD&DoIP Protocols
5. 6 BASIC FUNCTIONS
6. 28 SPECIAL FUNCTIONS
$169 To Get One Vident iSmartDiag 510 PRO BT OBD2 Scanner>>>
For more details, feel free to leave your comments or send us a message.
Hello, I m beginner in Chuptuning and I have a few questions. Firstly, can somebody help me with a good solution dor DPF and Adblue off in MD1CP014 and secondly check my mappack for this ecu? How to seleck driving mode maps for editing, are there any tips on which one is responsible for what or only trial tetod?
(12-12-2024, 05:50 AM)panreciu Wrote: Hello, I m beginner in Chuptuning and I have a few questions. Firstly, can somebody help me with a good solution dor DPF and Adblue off in MD1CP014 and secondly check my mappack for this ecu? How to seleck driving mode maps for editing, are there any tips on which one is responsible for what or only trial tetod?
![[Image: Vident_iSmartDiag510_510_PRO_1.jpg?v=1733903160]](https://cdn.shopify.com/s/files/1/0072/5424/5449/files/Vident_iSmartDiag510_510_PRO_1.jpg?v=1733903160)
![[Image: Vident_iSmartDiag510_510_PRO_9.jpg?v=1733904345]](https://cdn.shopify.com/s/files/1/0072/5424/5449/files/Vident_iSmartDiag510_510_PRO_9.jpg?v=1733904345)
