hi bros,
i need fuso canter 24C64 mileage repair

has 17919km  i need 19200km

Hi,
did anyone successfully red dash form Renault master 3 based on Fujitsu MB96F6A4RB with vvdi prog?,
in best case i can read files filled with '00'

Thanks in advance!

Hello, 

Can somebody help me with the mileage of this dash? It has 258xxx km and need 170253.  Inside it has an 9S12XHY256.
I can make the ABS with OBDstar but for some reason doesn't let me do dash. 

Thank you.

Attached Files

dash traffic 3 258xxx (dflash).rar

2

1.06 KB

Download

Hello,

I have the stock bin for my truck attached. Is anyone willing to turn off DPF/EGR/DEF for me?
No tuning, just remove emissions.

Thanks!

Attached Files

2020 F350 6.7.rar

16

2.07 MB

Download

I have retrofit the headlights with xenon on a5,changed the central electrics ,can i remove the cp from central electrics? I have odis v24 but i think it wont work because now i have another module installed....i need schrot to work

Hello, what version of ISTA do I need to have to connect to E61. I have K-DCAN cable.
I need to have the version that allows programming, I need to reset the system time. After adding VIN and coding SGM.
I downloaded ISTA+ but it did not have the programming option and it was not possible to do it, and ISTA/P with loader 6.6L does not see my interface.

Could someone please explain me where the srs module located on 2014 gl450 

Vin# 4jgdf7ce6ea436333

Hi
i put a Peugeot 208 GTI into a DS3 complete with the wiring loom and ecu
the ecu was changed from MED17.4 to MEVD17.4.2
the engine is working well but i have a few configuration problems and also can bus problems
is there someone who is familler with these ecus that can change the configuration?
also i need to tune this car 

Thanks

This manual contains procedures for diagnosis, maintenance, adjustments, minor service operations, replacement of components (Service) and for disassembly and assembly of major components (Unit Repair-Overhaul).

Mega Link : https://mega.nz/file/oHtBwI7I#sSRZ1my7rW...fSX5CjG2tM

Hi

Can someone tune 8HP in this Jeep WK2 ? I need standard tuning for 8hp and better downshifts (in stock car have high gear and very low RPM 1100-1200).

Code in flash 1 or 2 ?   Thanks

Attached Files

Thumbnail(s)
   

Hello dear mhhauto Members.
The ignition of the W220 brand vehicle was turned on but did not allow it to start.Using the star fault diagnostic device, the P1570 error was seen in the system checks. The explanation stated that the FSB did not allow it to work. I removed the EIS from the vehicle and read it with the VVDI prog (1D69J) MCU. I also read the key MCU but it was seen to be almost completely empty. Can you help me repair the file? Thank you in advance.
EIS MCU1 FILE https://mega.nz/file/KaABTQQS#43M8eT...nRHL2CXhXVaH4o

Hello, good afternoon, I don't know where to start. I have a mega cloud and there are viruses in some files, many are cracks and others are Trojan viruses etc.My question is, I have 600GB of personal stuff and programs. Is there a way to clean up my cloud and if so, how to lose the least amount of information? A good friend tells me to use Deep Freezer and another to use a virtual machine to clean and download everything.I need the name of an antivirus that can clean my system without damaging everything please. Any suggestion will be well received. Sorry for my English.

Hello,
anyone have good solution for md1cs006 mb?
davinci dont reconize fap i need fap more adblue.
If you want, you can add just fap to davinci's adblue file

Attached Files

md1cs006.rar

5

584.16 KB

Download

Hello my good people i have a DTC 3702 , with Launch, on this car and the check engine is red. I tried to erase it with davinci but no succes, anyone willing to help

It is Siemens/Continental MDS80 ECU

https://mega.nz/file/3zJwxAZb#okU47agHki...z_jNi5XSJc

Thank you all with respect

Edit: The error in davinci 3702 is off as it says

Hi, m8s!
I bought ignition switch with one key. I tried to pair this donor key to the car with Autel IM608, but unsuccessfully. The immo lamp is blinking all the time, though Autel says that pairing is successful.
The immobilizer module is IM860 116RI-000072 with MC9S08EL32 on board. I read the EEPROM and saw that the key is written to the file. After that I tried to write another chip to the dump with Autel. I used universal Xhorse chip generated as 8E. That changed nothing. The immo lamp is blinking, the car doesn't starting.
I really don't know what to do more. Can it be that immo lost synchronization with ECU?

ECU is Delphi MT60 part number is GM 25183774 AAWP

Hello Sid807evo with cem 1m15y xdt384 need help to synchronize. ABS 000050073010. thanks in advance.

Attached Files

volvov50212.rar

2

1.15 MB

Download

Hey guy can some one find me SVRL and SVBL maps of this file?

Attached Files

Scirocco 2.0 TDI.rar

4

97.77 KB

Download

Anyone else having problem getting the TGFlash datalogger to work?
It has never been working for me. "Error: Can´t read datastream"

Tried with ENET and Scanmatik on three different computers 

Hi, can someone make Stage 1 file for my own Audi S3 8P CDLA?

SW 8P0907115AP

original in attachment

Attached Files

ori.zip

2

856.13 KB

Download

Hello to everyone,
could someone help me with mileage correction for this used dashboard?

honda SH my2017

I read eep 93C66 16bit, I need 17.000km

thank you in advance

Attached Files

93c66 16 bit.rar

3

401 bytes

Download

i, 
I have a phaeton with lost original kessy. 


I read ecu with flex and read donor kessy.


CS:
9FBF5F533F7E00
MAC:
D7108A7F
CONFIG:
37E554
PIN:
07660
ECU STATUS:
Learned



but abrites needs powerclass to adapt kessy, how can i find it ?

Attached Files

dump.zip

3

909.1 KB

Download

please remove

Hi guys I have a problem with a Mercedes C w205 year 2014, I have done already some Mercedes with Yanhua and it worked great, but i bought this can filter and it dosent work, I will post some pictures of the filter maybe someone had this issue before. I already tried to bridge "s1, s2, s3"  connection and it dosent work any help would be appreciated. I want also to mention that the calibration i do with smok and the cluster its changing the mileage on dash but it dosent remain. Thank you!

Attached Files

Thumbnail(s)
           

[font="MHH Font", Calibri, sans-serif]Please code [/font][font="MHH Font", Calibri, sans-serif]Delphi RCD510.[/font]



[font="MHH Font", Calibri, sans-serif]VWZ4Z3L11155529[/font]



3C8035195


[font="MHH Font", Calibri, sans-serif]Thanks[/font]

Hi, can someone do adblue + nox off for me? Its MD1CS004

Attached Files

VW_MD1CS004_INTERNAL-FLASH.rar

9

2.43 MB

Download

so long story short. i ordered topdon found out that they have 1000 dollar scamscription on all of their phoenix products
which makes them useless for a home use to work on personal cars when you want programming features.

then ordered launch which has same features but cheaper and subscription is cheaper.

long story shorter. topdon was a total failure at every step of our interaction.
and i ended up with a topdon scanner at my doorstep and launch scanner at my door step...

out of curiosity i opened the topdon box and they sent me a used unit that looked like it was in storage for 10 years then handled by warehouse hulk/bear that spilled coffee allover the box all the seals were already cut etc

anyway now i have to deal with returning that junk and wasting more time

but when comparing them i noticed alot of labels and stickers and cables and accessories are identical.

so im assuming they are all made at the same warehouse?

i noticed when i try to use quick reply most of the time it doesnt let me post. i have to copy text and then paste it into regular reply screen