Hi i have made a mistakte and lost the eeprom oft ecu from an insignia 2.0 with edc17c19 (Bosch 0281 017 453) sw 1037529600.
i read the ecu with kessv2 but when i want to write the tuned file i only could do it with my k-tag.
After i installed the ecu in the car, the car doesn't recognize the motor ecu.
There is something wrong with my eeprom i think but i made the mistake not to backup the eeprom also when i startet.
Can someone help me with this please?
thanks
Newbie here, i think i burned my ecu testing diy supercapacitor battery... I have extracted the eprom and flash from original ecu and i have found the donor ecu (same part number).
What are the steps involved in cloning this ecu? I have BlackBox AMT BST tool i am able to read and write as stated above...
Hi
I need to lower the required oil pressure.
At idle, the required pressure is approx. 3bar.
I have to reduce it by approx. 0,6-0,7 bar over the entire rev range.
I don't know how to deal with it, so I will gladly pay for help.
I bricked CITROEN C5 DCM3.5 2.0 HDI by obd... Now the ecu is not recognized, i have the original OBD read + JTAG on boot.
Is there anything we could do to revive this ecu?
Below are the files on RAR.
Thanks in advance!
I have a Skoda Fabia with DSG transmission. 03C906027CE ecu which is a MED17.5.5 and I need to immo off. I already try couple solutions. After immo off with EDC17_E2P_Immo software car works but some faults on it ECU(P160A) Immobilizer(B104A) and I have fault on a cluster "safe" and EPC lamp. Solutions bad or can I solve this problems?
Address 01: Engine Labels: 03C-907-309-V1.clb
Control Module Part Number: 03C 906 027 CE HW: 03C 906 027 CE
Component and/or Version: 1.4l R4/4V TS H15 9737
Software Coding: 00250012002400000000
Work Shop Code: WSC 65535 000 00000
ASAM Dataset: EV_ECM14TSI01103C906027CE 001011 (SK25)
ROD: EV_ECM14TSI01103C906027CE.rod
VCID: 66F38C6BE2C259D42F7-8032
1 Fault Found:
2783 - Internal Control Module Memory
P160A 00 [10100111] - Check Sum Error
MIL ON - Not Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Priority: 2
Fault Frequency: 1
Mileage: 200760 km
Date: 2127.14.31
Time: 03:40:59
I tried few times finde somthing about reset/correction mileage in abs vag cars and didnt find nothing what could help.. Now i have Audi Q3 2014 all done, only abs not... Abs numbers 5N0614109BA and it have mileage only in one place in channel 62 and it is lower by 15k km than was on cluster. Maybe someone knows what exactly the mileage recorded in this place is from? Or any idea how to tuch it? In basic seting dont see any resets only tpms reset.. I also doubt that any adaptation can help.. For sure none didnt make any adaptation by last 20-30k km.. Mayby flashing abs to newer sw?? Or f*ck up codding and fix it? Thank for any advice.
This car comes to me after a minor accident with a motorcycle at about 60 km/h, all the airbags exploded and I have to replace them
But the funny thing is that the airbag light does not come on on the dashboard when I turn ignition on
while I have 6 DTCs communicated by the SBS module (B1801, 1806, 1811, 1816, 1901, 1906)
From what I know, the airbag light should come on every time I turn ignition on.
Am I right?
Can someone help me by telling me what can prevent the airbag light from coming on?
This car comes to me after a minor accident with a motorcycle at about 60 km/h, all the airbags exploded and I have to replace them
But the funny thing is that the airbag light does not come on on the dashboard when I turn ignition on
while I have 6 DTCs communicated by the SBS module (B1801, 1806, 1811, 1816, 1901, 1906)
From what I know, the airbag light should come on every time I turn ignition on.
Am I right?
Can someone help me by telling me what can prevent the airbag light from coming on?
Hi all. I've been trying to enable the blue welcome light without success on my 2017 W213 with multibeam.
In HLI_FL253 and HLI_FR253 modules, I tried setting the PLUC_HLI_Ch3_NSI_b to "off" (originally on) and PLUC_HLI_Ch3_NSI_blau_b to "on" (originally off) as well as channel 2, since those are both channels for the DRL.
However, the blue light does not turn on even after this change. Is there a setting I am missing, or is the blue LED hardware not present on USA headlights?
So I was in the process of replacing the ECU on a 2013 PB I20. I mistyped the pin code for the original smartra and locked myself out (silly) left it on for the hour, neutralized the original smartra with the original ECU plugged in, swapped over to the donor ECU and I attempt to read the new IMMO pin code by I receive the message "This vehicle does not support this function" I need the pin code to program a key and get this vehicle started
Digiprog 3 V4.94 is a cost-effective mileage correction tool, which supports multi-language and full range of vehicle till 2012. V4.94 digiprog 3 is latest version of Digiprog3, add more car models on the basic of V4.88. Digiprog 3 v4.94 Odometer Highlights 1. Latest software Version: V4.94
2. Support Multi-Language: Deutsch, English, Espanol, French, Portuguese, Italiano,Turkish, Nederlands.
3. Can be updated: Need send main unit back, this version cannot update by e-mail.
4. The main unit with USB upgrade interface and FTDI chip
Digiprog 3 v4.94 Odometer Functions:
1. The Digiprog 3 is the leading system for setting and programming digital speedometer.
2. The Digiprog 3 is the system, with modern hardware and latest software tachometer and speedometer repair adjustment for everyone in the simplest way possible.
3. You can use the Digiprog 3 for all speedometer, and engine control units, operating hours counter, keys, memory error, motorcycles, etc. easily programmed.
4. You get the unit of course with all the necessary cables as well as an image and textual manual.
Digiprog 3 v4.94 Odometer Other Functions:
Service interval adjustments and settings
Assyst processing
Fault memory read-erase
EEPROM programmer
Integrated PC communication
$129 To Get One Digiprog 3 4.94 Full Set Version>>>
Want to know the support list or more details, feel free to leave your comments or send us a message.
Hi,
after programming new key for X-trail T31 now cant start engine
I-key error on cluster, cant programm transponder for car
Have autel KM100, Obdstar X300DP, xhorse but cant to do
Who can help ?
Hi
i have a dacia lodgy edc17c84 with a turbo problem..but in workshop change turbo and pipes revised and more test but dont find the problem,
car have limp mode and dtc p2263 in some bit km...it sems turbo less blow
im thinking in a temporal solution..find map lim mode for difference blow turbo,i think it is about 250mb? and raise this limit to 500mb
i can find some some maps..
limiter turbo presure on 223A8C,223BAA 8x8 and 207C72 16x10
variable geometry on 207C72 16x16
Turbo pressure consig on 232976 16x16
but i cant find map for difference turbo presure limp mode ...someone can see this map ??
Hi anyone got access to audi tpi need abs tsb tpi svm code. Their is a update but audi wont give it or do it as they know i have a remap. They confirmed their is one as i have the wider 255 tyres on front so get traction kicking in too much.
Greatly appreciated if i can get it.
Thanks
![[Image: 4_a78ebbc5-1bf6-4a9b-a579-67d015b619a5.j...&width=493]](https://www.vxdas.com/cdn/shop/products/4_a78ebbc5-1bf6-4a9b-a579-67d015b619a5.jpg?v=1558351291&width=493)
