Hello. Can anyone give me immo off solution for this ecu? Need to test on car with a second hand unit to check a fault. Flash and EEprom bench read attached. Thanks.
Hi, I have a VW Sharan 2013 with ECU EDC17C46 to which I removed the ADBLUE but when I remove it the Start-Stop no longer works, could someone help me to remove the adblue well?
Hi everyone
I want to buy a new tool
please is after experience who can tell me which tool is the best
who can tell me which tool is better between FoxFlash and KT200Plus or if there is another tool comparable with them
thank you
Hello. I need to reset crashdata in SRS from Mazda.
Part nr BHPD-57K30C based on Infineon TC332LP-32F chip.
Chip is read protected, is there any change to change it for another one?
Or is it possible to replace that module with another part nr? used one?
Good day
Please I have issues with a ford f150 Hybrid 2023 with no start, stop safely is displayed on the screen I diagnose it I found the following DTC U301200AE in the battery Control module. Please what should be the possible cause and how to resolve it.
Thanks
Can someone help me to clear crash data on this attached file
The file is from a MY2010 Rav4 2WD Manual gearbox
By the way I am really surprised that the content of this eeprom is almost empty. Is this normal? For your information I have read that eeprom several times and with different programmers and I have the same result.
XTOOL TP150 TPMS Tire Programming Tool allows you to effortlessly relearn, reset, and activate TPMS sensors, specifically designed for compatibility with the XTOOL TS100.
XTOOL TP150 TPMS Programmer Highlight:
Works on Both 315Mhz & 433Mhz Sensors
Relearn All TPMS Sensors
Activate All TPMS Sensors
Check ECU-ID Matching Status
Check Sensor Real-Time Data
Program XTOOL Sensors
Program Multiple Sensors Simultaneously
Diagnose TPMS System: Read and clear TPMS codes
Reset TPMS Warning Light
Check OE Sensor Information: Check OE Sensor Brand, Part No., sensor frequency etc.
Test Records
Built-In Rechargeable Battery
Internet Update via WIFI and USB Connection
Lifetime Software Updates
XTOOL TP150 Programming:
The user can use this function to program the sensor data to a blank XTOOL sensor to replace the sensor with insufficient power and not working properly.Provides Four sensor programming methods: automatic, manual and copy by activation.
1. Generate Sensor ID Automatically
2. Input Sensor ID Manually
3. Via Activate Copy Sensor ID
4. Via Read ECU Copy Sensor ID
XTOOL TP150 Diagnosis:
Check The TPMS Status
Check The Sensors Status
Clear TPMS Warning light
$179 To get one XTOOL TP150 TPMS Diagnostic Tool>>>
Want to know the support list or more details, feel free to leave your comments or send us a message.
Hey guys. I made a custom wallpaper in Photoshop featuring a C218 CLS 63, turned it over for dark mode, and decided to share it here if anyone needs it. Also, if you want a custom wallpaper with your car, let me know, and I'll do it for free when I have some spare time.
Hello! I have a problem that is really in my nerves. Got a gtd CUNA , tuned, all well everything is okay, but the problem is the car do not go past 210km/h . No smoke, egt not more than 835deg, with the stock software it goes to 250km/h, but tuned, something limits it's ability to go past 210km/h. vmax are off till 300km/h. Does anyone had the problem before ?I will atach my tune. Thank you!
currently on tuning a SLK R170 200 Kompressor with Pops and Bangs.
I got the fitting mappack for it in WinOLS but cannot get Car to make the desired sound.
It is a SIM4LE ECU
So far i have decreased the Angle in the Spark Advance Maps to -15 Degrees and lowered the lambda values in the injection base map from 0.938 to 0.8.
If revved to 3000RPM + there is a slight noticible pop but that is very very dampened.
The question at hand is what am i missing here?, do i need to adjust something in the air control maps to attain the desired condition or do i have to just got at the
other injection based maps on the ECU.
hello everyone, i have here at my shop a Audi A8 from 2008 that the costumer tried jumping it and right after that it started cranking the engine with everything turned off, ignition off and keys out of the car, so the costumer disconnected the battery and sent it here to my shop, now it does not crank on its own but it has no ignition response at all, the only thing it does is light up the odometer screen on the dash when connecting the battery and the seats move with the respective switches and that is all it does.
I have tried connecting VCDS but no response from any of the modules.
I am kind of struggling with this one because i dint really want to start putting new parts in with no real improvements.
Any help at all is appreciated
Hello,
I have Renault Kangoo ECU with immo problem.
reference 8200513076 / 8200582518.
TRW / Delphi DCM1.2
Inside is eeprom 95160.
Can anyone give me a Virgin file (biut not FF for whole file) to program this ECU to vehicle ?
I looking for virginise the eeprom dump from keycodes, to reuse the pairing original key+UCH to re-write the injector codes.
You will find here almost everything you are looking for about the Mitsubishi L200: maintenance manual, Common Rail system, electrical system, bodywork, engine...
![[Image: 470212180_1313905956278097_2293023497252...e=6765BFEC]](https://scontent.fbrs5-1.fna.fbcdn.net/v/t39.30808-6/470212180_1313905956278097_2293023497252375666_n.jpg?_nc_cat=102&ccb=1-7&_nc_sid=aa7b47&_nc_ohc=ePbs1lxxq6MQ7kNvgHoPTPV&_nc_zt=23&_nc_ht=scontent.fbrs5-1.fna&_nc_gid=A-keAqMu0oQTcNBfO2F2en6&oh=00_AYC5KOtqnwpuKiYRXlcVW65mpOzS5mp2Xi_GKxILzuNQdw&oe=6765BFEC)
![[Image: e6ce6e69ca3356f9dc5da5b052b2959f.png]](https://i.cdncf.xyz/e6ce6e69ca3356f9dc5da5b052b2959f.png)
![[Image: XTOOL_TP150_TPMS_Programming_Tool_1_1024...1734071256]](https://cdn.shopify.com/s/files/1/0072/5424/5449/files/XTOOL_TP150_TPMS_Programming_Tool_1_1024x1024.jpg?v=1734071256)
![[Image: 110.jpg]](https://i39.servimg.com/u/f39/18/85/91/29/110.jpg)
![[Image: background.png]](https://i.ibb.co/8zgfmZM/background.png)
or where I can find this or buy it.
