Hi i changed the cluster on a vw Tiguan 5n now the RNS315 needs a code but i don`t have it.
The serialnumber of the RNS is: VWZAZ2P0135366
The Partsnumber is: 3C8 035 279 E
so I have another of this old ELV/ESCL issue, since last issue I did them online, and it worked without problems. But as we all know, online is problematic right now - so I'm stuck.
Facts are:
0. Steering Lock Defective on dash. Only intermittent fault code 02825.
1. Original OEM ESCL, brand new, 25-Immobiliser MVB 123 is empty
2. Read CCM dump, parsed with two tools, got same PIN - 05988
3. 25-Immobiliser MVB 3 -> All zeroes (so no wait time active), and old ELV communicates (and has a correct VIN)
4. Manually pressed the switch in the ELV, so ignition comes on (without that, the MVB 81 was only XXX - now I got VIN)
5. Login code throws Error 22: conditions not correct / tool does not get SEED key. Tried with Vag Can Pro and ODIS
So can't login, tried disconnecting power supply, tried all other tricks I know.
Hello guys,
I'm looking for a file named v069063302ea__getriebe_DSG_RG5N. I tried to find it in Flashdaten but without success. I would be grateful for any help.
HELLO
Does anyone have a solution for this calculator MD1CS003 0281 037 198 REF 9841351080
I want the possible reference to replace the calculator before the year 2021
Hello everyone need good crash clear for this autoliv 603201200 from a 206 peugeot. Already try airbagcrashclear and tachosoft and still airbag light on.
No errors after tachosoft reset, but airbag light still on. Ecu unlocked checked.
Really struglying to solve this problem.
Regards,
its posilbe on octavia 2 transfer from old to donor ecu only eeprom?
old ECU damaged with water and i have new with same partnumber and software. i need change ecu or i dont now copy only eeprom 93C from old to NEW?
Thanks
I need help for calculate mileage Fiat Bravo EDC16C39 95640
Last DPF replacement ori 237400 km need 167156 Last ECU Replacement 237400 km need 167156 Odometer 237632 need 167156 Last programming ECU 194215 need 0 km Oil change 7 need 4
Hello tuner's , i need the milage correction on ECU Delco e83 . I extract the eeprom from flash , i dont know if its correct . I do the odo 175321 , but i need at ecu too. If someone could help it will be nice .! need 175321
Best Regards
Gm flasher $300 Australia
DPS Patcher old version $100
Efilive Patcher old version to save bin files $100
ctz to bin converter $100
HP Tuners 5.1.58 $300
NVS flasher $150
Have a 2006 W164 ML350 4MATIC (VIN:WDC1641862A067252) and having current issue where Fuel Gauge is reading Full all the time.
Original Issue: Water damage on rear Sam - symptons indicators not working, fuel gauge issue (staying on empty, withough low fuel light and distance to empty ---) , rear tailgate lock mechanism etc etc - SAM totally fried
1. found a used Rear SAM (however out of a later model) - the part number matched my VIN on online parts catalogue
2. I took it to an independent who claimed to have access to online code. He advised that he coded the unit however could not get the fuel gauge working. everything else was working. he tried to convince me that the SAM part number was not matched to vehicle however I have a screenshot showing it does. residual Issue : fuel gauge issue (staying on empty, withough low fuel light and distance to empty ---)
After troubleshooting further ie checking resistance at REAR SAM I determined that the fuel pump/fuel sensor had an issue and replaced it. above Error Code c has been fixed.
Left Side Fuel Sensor troubleshooting/investigation
After removing the left side panel under seat, I determined that there is no fuel sensor on left side. there was only 1 fuel line. Also I have observed the following as part of further investigating on DAS
1. The instrument cluster Needles are testing fine however in DAS is reporting a Tank Capacity 32767.5 L ? see image attached 2. Also is DAS in rear sam coding it is showing for "Sensor Behaviour" = ODB Tank Sensor MY10 see image attached
I have tried to recode some of the adaptations offline and now the fuel gauge has moved to always on full.
my question is. could the 2 items above be causing the issue. is it possible to recode (offline) to set left fuel sensor to "Not Present" ??or does this need online coding. `
I have access to a VXDIAG. das /xentry and team viewer. Any help would be appreciated
Have a 2006 W164 ML350 4MATIC (VIN:WDC1641862A067252) and having current issue where Fuel Gauge is reading Full all the time.
Original Issue: Water damage on rear Sam - symptons indicators not working, fuel gauge issue (staying on empty, withough low fuel light and distance to empty ---) , rear tailgate lock mechanism etc etc - SAM totally fried
1. found a used Rear SAM (however out of a later model) - the part number matched my VIN on online parts catalogue
2. I took it to an independent who claimed to have access to online code. He advised that he coded the unit however could not get the fuel gauge working. everything else was working. he tried to convince me that the SAM part number was not matched to vehicle however I have a screenshot showing it does. residual Issue : fuel gauge issue (staying on empty, withough low fuel light and distance to empty ---)
After troubleshooting further ie checking resistance at REAR SAM I determined that the fuel pump/fuel sensor had an issue and replaced it. above Error Code c has been fixed.
Left Side Fuel Sensor troubleshooting/investigation
After removing the left side panel under seat, I determined that there is no fuel sensor on left side. there was only 1 fuel line. Also I have observed the following as part of further investigating on DAS
1. The instrument cluster Needles are testing fine however in DAS is reporting a Tank Capacity 32767.5 L ? see image attached 2. Also is DAS in rear sam coding it is showing for "Sensor Behaviour" = ODB Tank Sensor MY10 see image attached
I have tried to recode some of the adaptations offline and now the fuel gauge has moved to always on full.
my question is. could the 2 items above be causing the issue. is it possible to recode (offline) to set left fuel sensor to "Not Present" ??or does this need online coding. `
I have access to a VXDIAG. das /xentry and team viewer. Any help would be appreciated
![[Image: DSC03948.jpg]](https://blog-imgs-157.fc2.com/i/n/a/inazumi1723/DSC03948.jpg)
