hi i have done various tests to deactivate dpf adblue on jeep compass my'22, but i always get a warning when i turn on,
check DEF system,
no errors in memory, only this warning
reset done and adblue module disconnected.
i attach file ori who can help me i will be very grateful. thanks
i hawe problem with dtc off. i hawe fault water in fuel filter.but,filter iz new.i cant find problem. i try dtc off with davinci delux,project x but no success.can somebody help me?dtc is df293.p2264
I have a problem with a Skoda Octavia 2.0 2016, showing error code P164B00 - Oil Pressure Sensor.
I searched online for solutions, and most suggest replacing the oil pressure switch (brown one). I replaced two of these sensors but couldn't resolve the issue.
When the car is cold, it triggers the error and goes into limp mode (glow plug light) shortly after starting to drive. However, when the engine is warm, the error doesn’t occur unless I rev the engine above 3,000–3,500 RPM.
[font=Roboto, "Helvetica Neue", Arial, sans-serif]Hi I need a 2019 ph2 clio 4 patch to change the mileage with Renolink. I'm willing to pay for the patch and the explanation of how to use it[/font]
Vehicle has ongoing issue with p0402. Another garage has replaced both EGR valves and the cooler and Maf sensor with new genuine items from TPS (parts cannon - not me)
Relearns have been carried out with VCDS
Fault still persists and it’s now been passed to me. Has anyone seen anything similar before? Smoke tests shows all good. Soot loading and pressures all ok, exhaust flap operating properly
Hi can someone help with fuel priming pump in tank press on The pump has been renewed fault still present
2010 Skoda Octavia vrs 2.0l common rail diesel
I only have .5 bar at fuel filter, also should pump run when ign is switched on or only when cranked or engine running ?
Graphing fuel press it drops off on load above 2000rpm
DRV INJECTORS, HP PUMP all check out OK no leak
Thanks Joe
Hello,
I hope you can help me, because the second card is also causing problems at the moment, you have to press it for a long time until the car opens and closes, the chip card has 3 buttons (open, closed and light)
How can I then assign this to the vehicle, via Renolink, FRN 4 in 1 or via Renault Can Clip?
With Can Clip 159, it doesn't work for me even though I entered the code 5938, with Renolink I was able to learn the WFS pill.
But my ZV and the Keyless Go don't work, according to the clip the antennas are good and no RF data can be received.
What is meant by the H.F data? The hands-free?
Has anyone ever made a stranger's card via Eeproom and then assigned it to their vehicle?
Do you need to do more with Renolink than this?
Ignition must be off.
Doors open.
Do all doors have to be open?
Then proceed:
OBD cable connects to notebook/vehicle
Extra > Keys
Button "Read PIN", "Connect", "Start Learning"
Insert cards one after the other
Then click on the “validate” button
Then click Disconnect again
And everything should work including ZV, handsfree & starting
It is one
Renault Espace IV
2.0DCI
173 hp
BJ. 07.2007
with sensors in the doors and hands-free
Hello, I have a problem with Focus MK3 2014 2.0 TDCi 163 kw.
I updated the PCM software via Forscan and now the engine runs very badly, almost does not respond to the accelerator pedal.
The whole process was without complications. How to repair the car, how to return to the previous version of the software, to fix the problem.
I will also add that previously the car had an automatic gearbox, now it has a manual gearbox
Does anyone have an idea how to deal with this problem?
This truck was deleted previously by using a stand alone tuner (bully dog) but ecm and tuner was stolen
I installed a new ecm and programmed it but I need full delete, no codes and no messages on dashboard please, so I'm looking for a proven solution, I paid two people and both couldn't do it
I'm looking for a CAS file R0042JL_00423Y.0ba, it should be in a version around 45. I have V41 (Jan 2011) and V50 (July 2013), the first is too early and the second is too late.
hello
anyone possible help this map sensor calibration data /[font="Helvetica Neue", Helvetica, Arial, sans-serif]0261230439[/font]/
many MB use 220 250 cdi
after 2019 a45 and a45s
need older a45
