Hi , i have Jeep cherokee 2018 model 2019 from usa with uconnect 8.4 Delphi without navigation and i need to make EU conversion to have Eu language .Its possible ? any options? I know harmann and Panasonic can be done but abouit delphi i cant find any thing
Hello. Does anybody know the reason w213 facelift with ntg 6 not ahowing correct location. Did map update and the same. Change gps antena and the same. Its showing somwhere lost at the sea. While the car driving the maps move normally. Could not diagnose because no certifcate from xentry. But does anyone have a guess. And i almost forgot i have a notifciation for software uodate which is paused at 89%.
I need someone who can help adapting a used ECU (DCM 3.7) in a seat ibiza 1.2TDi (the old one has defect), ive got passthru, just need someone with the software who can adapt the new unit.
Obviosly its a payed job.
Hi Everybody, Can someone help with Ford Ranger 2.2 2018 BCM repair/reset please.
Problem is fault codes wont clear on BCM.
read from i/o terminal.
(12-18-2024, 08:32 PM)suttipong77 Wrote: Hi Everybody, Can someone help with Ford Ranger 2.2 2018 BCM repair/reset please.
Problem is fault codes wont clear on BCM.
read from i/o terminal.
I have a problem with my car. The engine is making a very loud noise that seems to be coming from the right side of the cylinder head. This sound also moves towards the rear part of the engine. Could it be the timing chain or hydraulic lifters?
This step-by-step guide will help users successfully install and configure Renolink software. Follow these steps carefully to ensure proper operation, especially when using clone devices.
1. Install the Software
- Download the software and proceed with the installation.
---
2. Copy Cracked Files (For Clone Devices)
- After installation, **copy the cracked files** to the folder where Renolink is installed.
---
3. Configure Interface Speed
**Important:** After installation, you **must change the interface speed** to `1000000`, or the device will not be detected by the program.
Steps to change the speed:
- Open **Ifprep2** as **Administrator**.
- In the program, click **"Interface Prepare"**.
- Change **BR DEVICE** setting from `115200` to `1000000`.
---
4. Blacklisted Clone Serial Numbers
Here are the serial numbers of blacklisted clone devices:
- 113010778246
- 113010839547
- 113010854133
- 113010872966
- 113010952269
- 113010979036
- 113010979327
- 113010980410
- 113010996014
- 113011105733
- 117010079935 (ELS27)
- 117010162182
- 117010177500
- 117010269473
If your clone device matches any of these serials, it will not work.
---
5. Generate License File
1. Open the **license generator** from the downloaded folder.
2. Click **Read Interface Info**.
3. Select whether your interface is **original or clone**.
4. The generated file will be created on your **Desktop** in a folder named **DAT**.
5. Rename the file to **renolink.dat**.
6. Copy the **renolink.dat** file to the folder where Renolink is installed.
---
6. Final Step
- Open the Renolink software and enjoy!
---
### Notes:
- Always run **Ifprep2** and other tools as **Administrator**.
- Double-check the interface speed setting; incorrect values will prevent detection.
Hi everyone, I have a SM2 pro clone that works with xentry 2024 and I noticed a strange behavior during the diagnosis on my GLK 220. Sometimes it performs a correct scan, sometimes it freezes at the beginning giving a communication error. I noticed that even entering the current data tab it freezes 9 times out of ten. The other day I had to perform an adaptation for DPF replacement and I tried for a whole day to connect always with the same "communication error" until after a long time I managed to access and complete the operation. Now I know that it is not a Mercedes SD but I wanted to know if the defect could be due to the poor quality components of the SM and if so how could I intervene or do I have to settle for what I can sometimes do. Thanks in advance and Happy Holidays to everyone
hello
i have bmw x5 bdc f15
with vvdi2 downgrade programming some problem
finally i chnage bdc & now all ok
from ecu orignal isn recover data
but one problem keyless entry not work
central lock working
i have orignal 95256 left side orignal data , but right side 95256 no data
my isn - 23F80E71D7B25304DB1E03CE8D150F6B
below attach both 95256 eeprom data
Hi guys.
Does this ecu have som otp sector or something like that? Or I can cust copy eeprom and flash file form old ecu to new one? Never did anything on this ecu
Thank you very much.
I have an Isuzu D-Max 3.0td my2007 with a dead ECU. I can't find any replacement with the same part number. Does anyone know if it can be cloned to a different part number ECU (same model btw)? Both from a 3.0, but mine has a manual transmission, replacement is from an auto. I have a full backup with the same sw as the dead ecu.
