Few days ago when i saw snowflake icon near to my battery percentage and (normaly it disappears while driving or in mornings when i start my tesla) i realized that it wont disappear. what normaly i had is like if tesla has lets say 70% of battery it took 2% for night to heat up battery, but now when i park tesla on 70% it stays same 70% and snowflake icon wont dissapear.
Hello Sirs:
Is there a way to read and write calibration files from toyota prius 2015?
I used techstream, after making health check, it shows the following for engine: Calibration update Configure 34754100 Yes No A4701000 No
what does this mean? and is there any tools enable me to read and backup the original file and write a modified one?
Thank you.
Hello folks, is it possible to get a pin from vin?
I have an Opel Grandland 2019, BSI is EL5 and it's damaged. As i know it is encrypted, the ECM is also encrypted (DCM7.1A).
Itried to swap the processor but apperently the original Processor (SPC564B74) is the Problem.
hi, i can pay for solution of course i need to solve this car
i get car dead, i managed to connect giving ignition making a bridge in fuse, and i saw this:
i put elv emulator because original seem opened for other garage
i erase dtcs, and car starts fine
when i turn off the car some minutes, again car dead and u3000, if i erase dtcs i can start car.
ok i buy RFA second hand and with vvdiprog i clone it
same behaviour than before.
i put donnor data in donnor module, and adapt with AVDI (i tought maybe sw corrupted)
same behaviour than before.
i try to update sw with forscan, but only sw available is the last one,
ok so i try to flash last version, but i see this message because hw incompatibility:
anyway i have original files with vvdiprog, so i decided to continue, and i blocked the module
i can bring back because i have the original files, but can anyone give me correct VBF file? i see there is a lot, but AK seem not compatbile, forscan only has AK
Hi everyone,
I have an opel corsa C that after engine replacement it lost the pin and vin from original ECU.
if i read the pin code from ecu i read 0000, keys are configured.
I tried to get the pin code from dash with opcom unsuccesful,
Can I find the pin on BCM?
Hey everyone,
I'm currently dealing with a seemingly very unusual issue with my truck. After spending multiple days searching the internet, I found only one post discussing my exact issue. That post is on diag.net. However, the discussion on this post is restricted to diag.net pro members, and I am not eligible for the pro badge. If anyone has an account and would be able to send me screenshots of the discussion, please PM me.
Thank you!
Posted by: dzdzpwr - 12-15-2024, 06:45 AM - Forum: Selling Box
- No Replies
Hello
I am selling my WinMAF software, which includes many solutions for ethanol (E85) and already purchased step 1s. With WinMAF, when a solution has already been purchased for a similar calculator, the option becomes free.
The credit costs 25ht
The annual subscription is 590 € HT. This price includes:
• Technical support (SAV) and access to free options.
• 2 credits for power modifications.
• 3 credits for conversions to E85 via FlexFuel.
I have already purchased 5000 euros of options
I am selling at 2500 euros ttc
Do not hesitate if you have any questions or would like more information!
daewoo winstorm 2.0 immo off edc16c39 please help!
I disabled the immo, but the car worked for a month and the computer locked up again, I wrote the immo off file again and the car started up again. Help me with the correct file.
After reading with KT200(obd read) Ecu is dead on CAN(no comunication). Reading was finished and I think that some part of flash was erased during this proces.
Can someone help me out and repair this flash for me or give me any idea how to do it myself.
Hi All,
yesterday I got FIAT Croma 1.8 140ps (with opel engine Z18XER), the engine doesn't start.
It seems there is an issue with the CAN network, following errors have been read on two different days:
on 14.December:
===============
U1602 CAN line, Bus off / instrument panel Marelli 2
9016 No Steering unlock authorization from body, no signal // Steering Lock TRW2
U1701 CAN Network (NCM-NGE) // TSEERING TRW 2
on 10.December:
===============
9004 TEG presence congurent, signal not valid // steering lock TRW 2
9016 No Steering unlock authorization from body, no signal // Steering Lock TRW2
The CAN resistence between L/H is measured and it seems to be fine.
Does anyone have a clue what can be checked additionally?
Hi I have a problem with 2017 jeep renegade, in the instrument panel it tells me that the lane assist and fcw system is not available, I tried to do a diagnosis on the front windshield camera and it actually does not establish any communication with it. I tried to check the power supplies and they are correct, I read that this type of vehicle has a recurring problem for this camera, has anyone had this problem? the part number of the camera is 52061986. Thanks
The Renault 19 - Complete Workshop Manual (French) is a comprehensive technical guide designed for owners, mechanics, or car enthusiasts looking to maintain, repair, or restore a Renault 19. This manual covers all essential sections, including the engine, transmission, electrical system, suspension, and more. Written in French, it provides clear instructions, detailed technical diagrams, and recommendations for diagnosing and fixing mechanical or electronic issues. An indispensable tool to ensure the proper functioning and longevity of this vehicle.
Now i have downloaded 3 different Winols and they all are crap and virus. Where do i find a working software so a can lern to mange it ?
The last one a downloaded i dont even can import a file to and nothing works. it cant se my ecu files and if a drag them they disapear and a lots of crap comes up and ask me if i want to update to newer winols.
Please help me to find a good and working winols
Hello colleagues of the forum does anyone know if it is possible to remove immo to an ecu of honda fit 2007 with chip 13 .I pn 37820-RME-A71 can pay for the help
GM DPS Development Program System v4.53.0000 Complete Single MSI Installer - FREE
Might come in handy for some people this installer does the patches and everything as it installs so the only thing you need to do is import the certificate and password which is all there in the DPS folder once installed including the type4 dll files and utilities for setting the date back so the certificate never expires.
Readme.txt file is in the DPS folder once installed to explain everything.
Once again due to a stupid small dick loser on this forum making a complaint to Mega it has now been moved to Yandex Disk
You might need to make yourself a Yandex account to save the files to and download if daily download limit is reached.
![[Image: dtcs.jpg]](https://i.postimg.cc/SRsVPpVk/dtcs.jpg)
![[Image: forscan-rfa-sw-numbers.jpg]](https://i.postimg.cc/Px6QYRHc/forscan-rfa-sw-numbers.jpg)
![[Image: hw-incompatibility.jpg]](https://i.postimg.cc/1X20YVfr/hw-incompatibility.jpg)
![[Image: supposed-to-be-compatible-sw-versions.jpg]](https://i.postimg.cc/BnWcTDWq/supposed-to-be-compatible-sw-versions.jpg)
