I have a 2013 Tesla Model S that was involved in an accident, and the airbags deployed. Does anyone know if installing a used airbag kit (airbags + airbag control module) from a scrapyard is enough to make it work? If I do this, will I need to reset the crash data? If a crash data reset is necessary, which equipment can perform this?
Hello,
I need access to the workshop manual of the engine code ‘K9K U 876’ in order to change the oil and filters.
My question is:
Can a non-professional user (who does not own an independent workshop) buy a token on NewDialogys to access such information?
trying to flash CIC on E90 with WinKFP in expert mode. Doing it with ICOM NEXT + B Next adapter.
Configuration of ICOM is MOST_ASYNC. The performance is incredibly poor, having an alternating upload between 8 Kb/s and 24 Kb/s. I have read a lot of threads about problems with ICOM Next and MOST flashing, but firmware is newer than the release for the fix and the performance is still poor. Some people said that it is working fine with them.
Also tried Mode MOST_CTRL but that does not work at all. I am really running out of ideas. does anybody have an idea how to solve this problem?
Programming voltage and Checksum are activated in WinKFP config. Is there anything I should have a look at?
Hi,
I want to delete crashdata on my Airbag unit VW40 1EA…But i do a misstake and write Pflash instead of Dflash.Is there a way to repair the unit?I try to write the original Pflash but no success only 00 00 is in the Pflash stored.
Thanks
Thomas
I couldn't find any information by surfing our forum on the details of Mercedes Maintenance Services. On the dashboard of my car I have the message Service D to be done in XX days. In the paper version of the Mercedes service book I have as a Maintenance Service Message with the numbers 1,2,3,4,5... and not letters as indicated on the car dashboard "Service D".
Who would have the details of the actions to be carried out for a Service D (also see A B C D E ... ) ? Or where i can find it ?
Hi i need help changing shift point for dq250e.
now car change gear low 1200 high 4600rmp
i need low 1600 and max 4000
or by speed
1 -2 23,
2 -3 37,
3 -4 53,
4 -5 71,
5 -6 85 km/h.
i ready to pay.
Thanks
Hi guys.
Anyone willing to send me some map packs with ori files? Preferably .kp files since I’m using the demo version of winols. Don’t want to bite the bullet just jet and buy the software. I can’t really find much info outside the vagecumap videos. Preferably med7 or 9.1. Can’t really point out any obvious maps or patterns when looking at a file 😂 thanks in advance!
I have a question about Audi A4 2.0tdi automatic
To make it short, I bought it with a faulty engine, the engine was changed, I see that the DPF was removed, the car smokes, the temperature rises.
The radiator fan turns on at 115°C and turns off at 110°C.
I replaced the EDC engine, the car runs fine, I have a DPF error and the gearbox does not work
How to report an automatic gearbox on it
thanks in advance
Hello, i have a bentley continental GT 2004, car when i put key in ignition unlock the ELV but show me in cluster : IMOBILIZER ACTIVATED.
i buy another kessy with same code , move the eeprom same think.
i think my date from kessy is corrupted, can someone check or can move the data from old kessy to the new one ?
I pay for good solution !
I got a faulty dash on a Audi A3 8P (year 2005) 2.0 TDI with EDC16U1.
I installed a used dash with same PartNo, and done immo off on ECU.
Dash shows SAFE and engine only revs to 1000-1500rpm and max 10-15kph.
Can anyone check if immo off was done correctly ? Or is there another problem ?
Thank you very much
So I have a Chevrolet cruze 2.0 166hp automatic gearbox 2013,diesel engine. After I start the car i have traction control light, the gearbox works fine for 3 min and then nothing. I have changed the battery , it s brand new. I have changed the TCM and reprogrammed to the VIN. Same errors.i have 60ohm when I did the measurements so terminating resistors good. I have 2,3v can low 2.7v can high. I will add a photo with the oscilloscope measurements and logged errors. What can it be ?
Hello,
We have swap a 6 Gear box and now Cruisecontrol dont work in 6 gear.
I have search something in Damos but not 100% shure what i should change and not mutch time,
So i will ask someone knows this and can help with that. Ofcouse must not for free
Thanks
Hi guys
Wonder if someone can help me repair the BCM2 EEprom that was flooded. Car started, moved it few meters away and then turned off normally. No start since. Noticed the BCM2 sits in water, opened it and obviously some corrosion found. Repaired it but cannot start car since. It says Contol module faulty and on dash Ignition lock defective.
Thank you
Hello! i need a hand for retrofit the virtual cockpit on a Golf MK7 here the ori (MQB-LOCK(D70F3537)-V1-READ) and the donor file (MQB-LOCK(D70F3526)-V4-READ).
Someone with Abrites or Poldiag can try to make the matched file for be inserted on the virtual cockpit. Mine Poldiag will be available on January.
Readed with Xhorse Key tool pad plus with adapters.
Hello Guys,
I have an 4.5to crafter that car is locked on Straight VMAX 100kmh, i have try vmax off there was one 100kmh limiter that i have change, but the car runs still 100^^
Hello,
Ive bought chinese android radio from aliexpress, its working fine, but i have no idea where Connect wires with key1 and key2 description to get steering buttons working, anyone had same problem? Seller doesnt know how to and i cant find any usefull answer on google.
