In my mercedes s420cdi i deleted CAT DPF and EGR.
Ecu software was remap by good reputable tuner.
During service and replace several gasket seal i installed EGR block off plate.
After that B60 and b60/1 exhaust back pressure sensors has constant parameters (atmospheric pressure)
Car goes into limp mode witch fault code.
What is the best solution for this problem?
Relocation back pressure sensor, or delete it from ECU?
Im not sure how turbochargers will work without sensors.
Hi
I try to get a pretty nice popcorn with bang or maybe flames in my 1.9pd tdi ajm
I have modified the SOI(-15-(-10)),DOI(37-42), torque limiter (4500->00), n75 duty cycle(+15% at 4300rpm)
I have a pretty nice popcorn but without the bangs, I tested it when i travelled with the car over 20kms(so its warm, pretty warm)
I dont know what to do. I try to make the perfect software, I already have 24 version but no one have the bang or the flames
Please help me
I need immo off solution or ecu clone solution for this VW Amarok EDC17C54 ECU.
I have attached a flash and eeprom file from OLD ecu and New ecu.
I read ecu with original pcmflash on bench.
If someone can do immo off, need a proper solution without any DTC in ecu or cluster immobilizer warning. happy to pay for a good working solution as i requested,.
Can someone do immo off to my 1.6 gas engine SIMOS 7.1?
My keys aren't recognized anymore. Immo Active appear on the dash and the engine not starting.
I've attached the 93C86 read from the engine ecu 16bit mode.
Can someone modify my file to rise up the idle RPM to 920?
I need to rise up the idle RPM when engine is cold and hot from original state (780-800 RPM) to 900-920 RPM because of flywheel problem.
The flywheel is shaking and an ugly noise is hearing at standard idle speed so I need to rise it up to 900-920RPM even if engine is cold or hot.
Some cars can be adjusted by VCDS but not this one. The only way as I read on the internet is by modify the ecu file via WinOls.
I have attached the .org file. Is a Skoda Octavia 1.6 Diesel. Engine code: CAYC Ecu type: Siemens.
MEDC17 eeprom CRC tool - utility for correcting checksums in eeproms of Bosch ECUs: EDC17, MED17, MEDC17, ME17, MEV17, MEVD17.
Tool works with eeprom files, supported filesize: 32, 64, 96, 128, 192 and 256 kb.
Features:
- automatic CRC algorithm detection;
- supported 3 different CRC algorithms;
- built-in "foolproof" (calculation does not occur if the ori. and mod. files have different filesizes, different CRC types, the same file is opened twice, etc.).
I provide sevice SECURITY LOCK PASSWORD DVD TOYOTA, LEXUS.
If you want to do it quickly and reliably, please contact me. I will help you faster. All services are in the attached txt file.
Video: txt file
PRICE : 50$ - 100$ All model Toyota/ Lexus.
CAR INFORMATION:
Brand: Toyota LX600 Year: 2022
Model code: VJA310W-GKULZ
KATASHIKI
Infomation car on EPC
BEFORE: need input code Security
AFTER: DVD can be reused normally
All services are in the attached txt file.
Please contact me viaWhatsApp(informations find contact in my profile)
For urgent cases that you need to do immediately (ECU Security, Programming, 12 digit keycode...), if you send a message and there is no response, please call me. I will support within 5 minutes.
I had this car in for adblue, dpf and noxcat oxicat delete.
As i am not a user of automated sollutions i prefer nerding around with damos and after several attempts i got it all sorted with just the preturbo egt sensor and the lambda sensor left in the exhaust trajectory.
The issue i had though was that the fans kept spinning hard after the car shut down, for exactly 12 minutes.
The reason is that when egt sensors from oxicat are missing the ecu uses a replacement hot value and then has two maps for how long at which duty cycle it runs and an added delay time.
I post the manual sollution and the original file for you guys. Enjoy and a thanks or rep would be nice.
Hi guys, I have a question: it is said again and again that the ECU needs to be unlocked and/or the password needs to be read. Why? Which ECUs need to be unlocked? My MED17.1.21 too?
I swap w204 front sam. starter relay couldn't start the car ignition voltage is not present in one of the starter relay pin (kM) but it was working fine from the car it was what can I do? I fix another front Sam it started the engine all three front Sam d same part number is it a programming issue please any help my dm wattappe 08102236065 I will appreciate
I have a 2022 dodge ram 3500 6.7L and I want to do a full delete. Is anyone able to tell me what tool I need to use to delete it. Also, is anyone able to make a delete file for it.
![[Image: CRC-1.png]](https://i.postimg.cc/tZtvxcxD/CRC-1.png)
![[Image: CRC-2.png]](https://i.postimg.cc/NLBzcQ3n/CRC-2.png)
![[Image: CRC-3.png]](https://i.postimg.cc/fJbqVBTj/CRC-3.png)
![[Image: fMxvvVA.png]](https://i.imgur.com/fMxvvVA.png)
![[Image: EOi1eWD.jpeg]](https://i.imgur.com/EOi1eWD.jpeg)
![[Image: uAHQoWC.jpeg]](https://i.imgur.com/uAHQoWC.jpeg)
![[Image: lOOeWBe.jpeg]](https://i.imgur.com/lOOeWBe.jpeg)
![[Image: LwESCBx.jpeg]](https://i.imgur.com/LwESCBx.jpeg)
![[Image: ZvUU2Ht.png]](https://i.imgur.com/ZvUU2Ht.png)
