I provide sevice SECURITY LOCK PASSWORD TOYOTA, LEXUS.
If you want to do it quickly and reliably, please contact me. I will help you faster. All services are in the attached txt file.
Video: txt file
PRICE : 50$ - 100$ All model Toyota/ Lexus.
CAR INFORMATION:
Brand: Toyota NX350 Year: 2022
Model code: TAZA25-AWZLT
Infomation car on EPC
BEFORE: need input code Security
AFTER: DVD can be reused normally
All services are in the attached txt file.
Please contact me via WhatsApp (informations find contact in my profile)
For urgent cases that you need to do immediately (ECU Security, Programming, 12 digit keycode...), if you send a message and there is no response, please call me. I will support within 5 minutes.
I tried DPF & EGR off using Davinci but it didn't work.
The DPF was deleted by the previous owner and with no dtc so it could already be done.
I removed the EGR recently and would like to clear the dtc and correct the white smoke at hot idle.
If possible it would be great to tune it to stage 1 with popcorn limiter but if not that's also okay, I appreciate the help with DPF & EGR.
I'm not sure what info you might need so this is the readout from the MPPS.
Vin: WAUZZZ4F08N047248
Bosch Hardware Number: 4F0907401C
VW Software Number: 4F9910401L 0010
System Type Number: 3.0L V6TDI G040AG
Hey guys, I'm trying to flash a different OS into a controller. I can license the controller, but then it says unlicensed vehicle after I license the controller and attempt to write entire. I know EFILive you can force in a different OS no problem, but I do not have that software and device. Anyone know how to convert a HPT file to force into a controller regardless of the vin because HPT wont let me change the vin in the editor either. I know there is a way but right now I have wasted credits thinking it would work like it used to back before HPT restricted it. Thanks!
Hi. Need some advice please on my Audi 2021 SQ5. It was flood damaged with bent conrods. I put new pistons and conrods in and was just rotating it before I reinstall to check if anything was binding. I heard 2 distinct clunks as I turned it. I narrowed them down to under the timing chain/camshaft adjuster covers. I removed the covers and each of the tensioners is letting go during each rotation. I have added a short video. I did not lock the tensioners when I removed them. Is this a sign of defective tensioners that now need replacing or can it be something more sinister. It looks to be as if the tensioner gets under x amount of tension then releases which its not supposed to do. Thanks in advance for any advice.
Hello. Can someone help me with adding a used MED17.0.1 Ford Focus ecu? I add Launch or Autel (that is VIN) but then IMMO FAILURE is displayed. There are 2 errors in the ecu from incorrect immo data. There is an option in PATS to learn and reset the bcm ecu, but it cannot find the pin and a window to enter is displayed. Can someone help me?
Hello everyone,
I have Volvo S60 old ecu is damaged cant read file,
Can someone help me to sync CEM with ecu so i can start car
Attached ABS ID and original CEM dump and NEW ECU DUMP
Hello , I tried flap off on mercedes benz edc16cp31, fault code P2015 with davinci Deluxe Connector disconnected after solution and no dtc , but car still lost power Can anyone help with working solution In attachement original file Thanks in advance
Hello everyone. I have Skoda Octavia from 2013 and my Multimedia screen stopped working. Its the Columbus one. I found multimedia screen from same Skoda but facelift variant for very cheap price. The multimedia looks exactly the same but has different hardware and software numbers. I plugged the new one but the screen is is split into 4 for some reason. Anyway the multimedia is fully functional. I have fault code on 5F Information Electronics - "Multimedia wrong component is installed". Is there a way to code it and make it work on full screen?
Original one - Part Number: 5E0919605D, HW version: H50, SW version: 0022
New one - Part Number: 5E0919605J, HW version: H41, SW version: 1028
Attaching photo of how it looks when it is connected to the car.
Hey guys, working on a 2008 Audi A4 B7 with RB8 cluster. Client tried to program key after losing original. The wrote immo data file over the eeprom on the cluster using autel device. Now cluster does not load full and shows Def. I have a new key and donor cluster. What steps do I need to take with vvdi2 to adapt cluster, program key and get car function normal again and driving again. Thank you in advanced. Donor cluster is already installed. Also need to correct millage after. Twist key ignition.
I have a Audi a5 2.0 tdi dsg from 2017 with edc17c74 that I need to delete adblue, with davinci's solution Startstop function stops working, and my costumer wants the startstop to work...
I have attatched the ori and adblue off file
I am trying to change ECU on my Vectra OPC 2006, but I get as far that it asks me for a VCI code. I know that I can obtain it from ServiceBox but my accont is not validated yet.
Is there any other way to obtain this code from VIN?
Hello. So i have a sharan 1.9 pd AUY in garage. The problem was that its not starting good, needs a lot of crank to get to work. (7-10seconds of crank.
Changed: cam sensor 2x, crank sensor 3x
Checked: wiring (every single wire), ECU (changed too not helped)
also checked the tooth on the flywheel😂
The glow plug light was flashing after start, but i solved with a broken contact in fusebox. (after this the DTC P0605 disappeared compeletly.)
The code for crank sensor implausible signal never got away, can do anything after i clear the code and give a start it immidiatly goes back...
[font="MHH Font", Calibri, sans-serif]I've installed Xentry 09.2023, but I'm stuck on the VCI firmware update for VXDIAG. I've tried several solutions, but I still can't update it to make it work with version 09.2023.
Can you help me, please? What should I do? Thanks!![/font]
Trying to do immo off on above ECU however some one sent me wrong flash now i have no connection via bench pinout.
he suggested i restore original file using MPPS (boot mode).
However my original was read with fox flash - reading online it says fox flash does not do a full read on this ecu?
i have never used MPPS before is there some one who can advice / help or guide recovering this ECU and doing immo off on this car?
Had the car in garage over 5 weeks really need to get it out - i am happy to pay for a workign solution or guidance.
Attached is
Original file - read by fox flash
Immo off flash file currently written on ECU - ECU is Bricked
Also EEPROM immo off which this person suggested i use after recovering ECU.
![[Image: PKzHpp5.png]](https://i.imgur.com/PKzHpp5.png)
![[Image: SGIHv6v.png]](https://i.imgur.com/SGIHv6v.png)
![[Image: qIjptA4.jpeg]](https://i.imgur.com/qIjptA4.jpeg)
![[Image: MHKjwOC.jpeg]](https://i.imgur.com/MHKjwOC.jpeg)
