I have a Toyota Aygo (My 2008) that start for 2sec then dies , There is not any dtc and I can connect with all ecus so I supposed that the problem is immo , I tried to resynch manual with sort obd pin3 with 14 without lack .
Could someone do virgin the dump from immo box ?
Thank you
I need to repair a BSI magnetti Marelli NBC250A on a DUCATO Motor Home. The fuel gauge is not working.
First of all I tried to change the BSI and swap eeprom but not working because I m unable to read the FLASH NEC.
So I try to repair this function (fuel gauge) but everything seems ok on the board.
Do you have an idea ? Is there a solution to get the wiring diagram of the PCB ?
Thank you so much !
Nico
Hi to all! I have an Volvo V50, year 2008, 1.6 engine, that does not start. I need ECU and CEM sync. I don't know if the eeprom from CEM is good also. I have dumps from both CEM processors attached, and the EEPROM from ECU (EDC16C34 FOMOCO). I've also attached the ABS ID.
on my private GLC X253 om 651(253909) from 2017, although almost 3/4 full, the message "Check Adblue system, see operating instructions" appeared in the instrument cluster. I then still filled up AdBlue but message does not disappear, it is only missing about 7 liters. The AdBlue status cannot be displayed in the KI. Control unit SCR (scr02) is without error and fill level in the actual values is FULL but also a little too much 26 liters. In the CR43 engine control unit, the error is currently " Wrong message received from SCR. According to the test instructions, SCR work off errors, but is without errors. Meanwhile message in the KI (IC222) No start in 800KM . Message with Monaco successfully reset after unlocking, but it stays that way. Anyone have an idea?? Thank you
Hi, please help with speed limit off or set to 100 km/h.
Vw crafter
edc16cp34
I try by eep and vcds but dont work.
Car have tacho.
Limit is 90 km/h
Thanks and regards
Hello Guys! it's first time to use vw_flasher on simos18.10 scg, i did unlock ecu with the right frf file, at the end it stay to : Finalizing.....100 for 10 minutes, but nothing happens. I turn off-on ignition and no more comms with ecu. any hint to revive it? thanks
Please share what programs your using or why you don't below;
The threads I've found are a little outdated.
Current information may be beneficial and reduce infected files from being unintentionally shared.
I test with
virus total and in windows sandbox on some occasions.
I save a backup before adding anything new and keep another another back up from the time before last on a separate SSD
I run member ubu.tech Synaptic Killer v6 frequently, if you haven't you should.
Feel free to share any information or useful antivirus software activation methods.
Im trying disable ews in bmw E38. Tryied reset isn in dme and sync but is problem with connection dme<>ews box.
I attached both files ORI boot read and my ews off but not working.
The car issue is that BCM is locked for 960 MINS because of invalid pin code for immo now car is running but cannot add key and car needs to stay on for more than 16 hours to remove the lock. I read the eeprom of the bcm from Orange 5
IC: 95320RT
Can anyone remove the bcm lock from it? Or allow me to add key
I have attached eeprom file from a different car but same model and year that might help which is not locked
Hi everyone I try to clone my 2013 e89 z4 20i original mevd1729 into mevd1724. Done it, car start but into limp mode got turbo wastegate error and incorrect data anyone can help? Thanks
Hello, I have a problem with CEM from Volvo V50. CEM number 31254903. Inside two MOTOROLLA MC9S12XDT256MAL
I copied EEPROM and FLASH from two 1:1 CEMs but it doesn't work. What am I doing wrong? I copied VVDIPROG
Hello, I have a problem with an Opel Movano 2.3 100 kW. the car drives fine, but only at full throttle for a long time, ASR, ESP and Ignition Check messages pop up. Faults have occurred in the motor unit
010122- inlet air circuit, signal amplitude - maximum,
131a3a,131e3a, 13213a cylinder 1,2,3 injection control circuit, to many signal pulses.
Has anyone encountered this? or don't you have a workshop manual with defects? Thank you
Is there any way to run Vag Commander on Windows 10 without VMware (Virtual machine )
As i can see it uses same drivers as Inpa so will it work with them on Windows 10 ?
![[Image: Screenshot-2.png]](https://i.ibb.co/Hp6wgsd/Screenshot-2.png)
![[Image: Screenshot-1.png]](https://i.ibb.co/BVWys7z/Screenshot-1.png)
