Hello, I have a problem with an Opel Movano 2.3 100 kW. the car drives fine, but only at full throttle for a long time, ASR, ESP and Ignition Check messages pop up. Faults have occurred in the motor unit
010122- inlet air circuit, signal amplitude - maximum,
131a3a,131e3a, 13213a cylinder 1,2,3 injection control circuit, to many signal pulses.
Has anyone encountered this? or don't you have a workshop manual with defects? Thank you
Is there any way to run Vag Commander on Windows 10 without VMware (Virtual machine )
As i can see it uses same drivers as Inpa so will it work with them on Windows 10 ?
Hi need advice with skoda with nec 24c64 cluster and simos 10.22a
Car came with fault 1570, ecu blocked by immo.
Someone try change dash in this car but i dont know for sure what was done..
On dash is not SAFE and any error, i can read security block with no problem by any tool and have all data. Car have 2 keys and they are available..
Ecu in car is original from car, dash original , keys original
Hey guys, i have a strange problem. the ford fiesta already had a stage 1 and lambda off. i added pop and bang there and wrote it on the fiesta. after the software was up it popped but all of a sudden the engine light was on because of the lambda. after that i only put stage 1 and lambda off again and the engine light is still on. i also put the complete original software on it and deleted the error and then again stage 1 with lambda off but the light is still on. the error code is P0036
I have problem with renault master 3,fault DF1159 egr water pump control circuit below the min level.this renault master have 3 electrical pump,and all 3 pump working in actuation test.
I read and check ecu flash,flash is original.where could the problem be????
I try Read with launch,launch say fault code DF1359 First egr water punp control circuit below the min level.fault delete ok,but fault back after start engine.
Hello, can someone help me calculate the checksums of edc15vm+ golf 4 alh? I uploaded it twice using kt200II and kess v2, each time after uploading the ECU is dead. I desoldered the flash, uploaded the original and it works, but the modified file is not accepted.. I tried to run it through Winols and it shows that the sums are good. I don't know what's going on . Alternatively, I'm looking for someone who will do stage 2 golf 4 alh 216 injectors with checksums.the first file is modified and the second is original
I’m working on updating the APIM software on my 2023 Ford Taurus (Middle East version, also known as Mondeo in China). However, I’m running into an issue: the newer cars usually show an APIM update option in the software update tab of FDRS, but for my car, this option is not listed.
After some research, I found out that upgrading from my current build (22047) to the next version (23335 or 24058) requires a specific method that doesn’t involve the standard professional FDRS process. Once the APIM is upgraded to 23335, future updates can be done normally through FDRS software update tab or even Wi-Fi.
I’d appreciate it if anyone could guide me through the steps or tools required to perform this upgrade from build 22047 to 23335 using this alternative method. If necessary, I can provide a VIN associated with the 23335 build.
Thanks in advance for your help!
Attached are photos of the updates that I’m referring to.
Hello Everybody,
i load with DPS a Keyless entry Modul ( AstraK ) with the Original Software.
But Loading not work and after laod the Modul damage and i can´t load it again.
I have a 2009 w221 not communicating with the ism so car can't start, scanned the car with Star software can't get what is wrong , has anyone had this issue ? Ism was taken to another car communicating fine, another ism was put on the car still same problem no communication
I’m trying to do a e41 ecm upgrade with a mpvi2+ I keep getting an interface partially responding error I bought the pro feature set I have the credits really need to get this done would I be better off getting a mpvi3? Anyone had this issue
I need DPF+EGR off because of the black smog (Dirty evacuation pipe) and Stage1 if possible.
The DPF is already dead.
If I'm not asking too much, please separate the mod into two files.
One just EGR+DPF off and another one EGR+DPF+Stage1
I want to try both files and see the smog difference.
Hi,
i want to tune my 116i n13 with 100kw.
I saw the engine is the same as in 118i and 120i with 177hp.
So how much hp are possible? May someone has experience and can help.
Ecu file name Sim4.CBF
Request: 27 0B
Response : 83 F3 01[7F 27 22] 3F
Request : 27 01[/font][/size][/color]
Response: 83 F3 01 [67 01 59 CB] 04
can any one generate seed key ?
i also have attached some pictures too
As the title says. We put in used dsg dq250 in this 2017 2.0 touran. Car starts but doesn’t shift. It needs to adapt immo. Anyone able to do it remotely ? I have only vas 5054a and Odis-s 7 to work with.
. Alternatively, I'm looking for someone who will do stage 2 golf 4 alh 216 injectors with checksums.the first file is modified and the second is original
